LPC2888FET180/01 NXP [NXP Semiconductors], LPC2888FET180/01 Datasheet - Page 30

no-image

LPC2888FET180/01

Manufacturer Part Number
LPC2888FET180/01
Description
16/32-bit ARM microcontrollers; 8 kB cache, up to 1 MB flash, Hi-Speed USB 2.0 device, and SDRAM memory interface
Manufacturer
NXP [NXP Semiconductors]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LPC2888FET180/01
Manufacturer:
HYNIX
Quantity:
1 200
NXP Semiconductors
Table 6.
T
[1]
[2]
[3]
[4]
[5]
[6]
[7]
[8]
[9]
[10] Applies to 5 V tolerant pins.
[11] Accounts for 100 mV voltage drop in all supply lines.
[12] Only allowed for a short time period.
[13] Applies to pins V
[14] Applies to pins V
[15] Applies to pin V
[16] Applies to pin V
[17] Applies to pin V
[18] Applies to pins V
[19] Applies to pin V
[20] All the above tests were done on the Icetech LPC288x evaluation board. Here are the different configurations that need to be done to
LPC2880_LPC2888_3
Preliminary data sheet
Symbol
I
I
I
DD
DD
DD
amb
Typical ratings are not guaranteed. The values listed are at room temperature (+25 ˚C), nominal supply voltages.
Applies to pins V
V
External supply voltage; applies to pins V
Applies to pins V
External supply voltage; applies to pins V
Referenced to the applicable V
Including voltage on outputs in 3-state mode.
Applies to pins with a V
Applies to pins with a V
achieve the above numbers:
a) Resistors R7 and R8 on the board should be removed to reduce the power consumption on the LED’s D2 and D3.
b) The Analog-to-Digital Converter (ADC), the Dual-channel 16-bit Analog-to-Digital Converter and the Dual-channel 16-bit
c) The USB device controller is suspended.
d) All power control registers in the Clock Generation Unit have a value of 7h, and the Power Mode register in the Clock Generation Unit
e) The floating pins are set to output state.
f) The Event Router is configured in such a way that it will generate its wake-up output to the Clock Generation Unit with a rising-edge
= 40 C to +85 C, unless otherwise specified.
DD2(USB1V8)
Digital-to-Analog Converter are powered down.
has a value of 3h such that the output clocks of all spreading stages are disabled.
signal on the MODE1/P2[2] or the MODE2/P2[3].
Static characteristics
Parameter
supply current
supply current
supply current
.
DD(OSC1V8)
DD(OSC321V8)
DD(ADC3V3)
DD(DAC3V3)
DD1(CORE1V8)
DD(DADC3V3)
DD1(CORE1V8)
DD1(EMC)
DD(DADC1V8)
DD
DD
, V
.
.
.
supply of 1.8 V.
supply of 3.3 V.
.
DD2(EMC)
, V
, V
, V
, V
DD
DD(ADC3V3)
DD(DADC3V3)
DD2(CORE1V8)
DD2(CORE1V8)
for the pin, which must be present.
…continued
.
DD3(USB3V3)
, V
DD1(EMC)
.
DD(DAC3V3)
, V
, V
DD(DADC1V8)
DD1(FLASH1V8)
Conditions
32.768 kHz oscillator stops;
12 MHz oscillator runs;
external DC-to-DC
converter supplies 1.8 V
32.768 kHz oscillator runs;
12 MHz oscillator stops;
external DC-to-DC
converter supplies 3.3 V
32.768 kHz oscillator stops;
12 MHz oscillator runs;
external DC-to-DC
converter supplies 3.3 V
, V
16/32-bit ARM microcontrollers with external memory interface
, V
DD2(EMC)
Rev. 03 — 17 April 2008
, V
DD4(USB3V3)
DD5(IO3V3)
, V
, V
.
DD1(FLASH1V8)
DD2(FLASH1V8)
, V
, V
DD1(IO3V3)
DD6(IO3V3)
, V
DD2(FLASH1V8)
, V
.
DD2(IO3V3)
LPC2880; LPC2888
[20]
[20]
[20]
, V
, V
Min
-
-
-
DD(OSC1V8)
DD3(IO3V3)
, V
, V
DD4(IO3V3)
Typ
0.97
1.27
1.27
DD(OSC321V8)
[1]
© NXP B.V. 2008. All rights reserved.
.
Max
-
-
-
, V
DD1(USB1V8)
30 of 43
Unit
mA
mA
mA
,

Related parts for LPC2888FET180/01