ISPPAC-POWR1014A LATTICE [Lattice Semiconductor], ISPPAC-POWR1014A Datasheet - Page 33

no-image

ISPPAC-POWR1014A

Manufacturer Part Number
ISPPAC-POWR1014A
Description
In-System Programmable Power Supply Supervisor, Reset Generator and Sequencing Controller
Manufacturer
LATTICE [Lattice Semiconductor]
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISPPAC-POWR1014A-01T48I
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
Part Number:
ISPPAC-POWR1014A-01TN48I
Manufacturer:
Lattice
Quantity:
176
Part Number:
ISPPAC-POWR1014A-01TN48I
Manufacturer:
LATTICE
Quantity:
494
Part Number:
ISPPAC-POWR1014A-01TN48I
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
Part Number:
ISPPAC-POWR1014A-01TN48I
Manufacturer:
LATTICE
Quantity:
20 000
Company:
Part Number:
ISPPAC-POWR1014A-01TN48I
Quantity:
85
Part Number:
ISPPAC-POWR1014A-02T48I
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
Part Number:
ISPPAC-POWR1014A-02TN48I
Manufacturer:
LATTICE
Quantity:
947
Part Number:
ISPPAC-POWR1014A-02TN48I
Manufacturer:
Lattice Semiconductor Corporation
Quantity:
10 000
Lattice Semiconductor
Figure 27. ispPAC-POWR1014/A TDI/ATDI Pin Selection Diagram
Table 10 shows in truth table form the same conditions required to select either TDI or ATDI as in the logic diagram
found in Figure 27.
Table 10. ispPAC-POWR1014/A ATDI/TDI Selection Table
Please refer to the Lattice application note AN6068, Programming the ispPAC-POWR1220AT8 in a JTAG Chain
Using ATDI. The application note includes specific SVF code examples and information on the use of Lattice
design tools to verify device operation in alternate TDI mode.
VCCPROG Power Supply Pin
Because the VCCPROG pin directly powers the on-chip programming circuitry, the ispPAC-POWR1014/A device
can be programmed by applying power to the VCCPROG pin (without powering the entire chip though the VCCD
and VCCA pins). In addition, to enable the on-chip JTAG interface circuitry, power should be applied to the VCCJ
pin.
When the ispPAC-POWR1014/A is using the VCCPROG pin, its VCCD and VCCA pins can be open or pulled low.
Additionally, other than JTAG I/O pins, all digital output pins are in Hi-Z state, HVOUT pins configured as MOSFET
driver are driven low, and all other inputs are ignored.
To switch the power supply back to VCCD and VCCA pins, one should turn the VCCPROG supply and VCCJ off
before turning the regular supplies on.
User Electronic Signature
A user electronic signature (UES) feature is included in the E
consists of 32 bits that can be configured by the user to store unique data such as ID codes, revision numbers or
TDISEL Pin
H
H
L
TDISEL
ATDI
TDI
JTAG State Machine
Test-Logic-Reset
1
0
Test-Logic-Reset
Yes
No
X
Q
CLR
SET
ispPAC-POWR1014/A
TMS
33
JTAG
TCK
Loaded at Update-IR
IDCODE Commands
IDCODE Instructions
Loaded at Update-IR
2
CMOS memory of the ispPAC-POWR1014/A. This
4 Consecutive
4 Consecutive
Yes
No
X
ispPAC-POWR1014/A Data Sheet
TDO
ATDI (TDI Disabled)
TDI (ATDI Disabled)
ATDI (TDI Disabled)
Data Input Pin
Active JTAG

Related parts for ISPPAC-POWR1014A