AAT3236IGV-2.8-T1 AAT [Advanced Analog Technology, Inc.], AAT3236IGV-2.8-T1 Datasheet - Page 9

• Manufacturer Part Number: AAT3236IGV-2.8-T1
• Description: 300mA CMOS High Performance LDO
• Manufacturer: AAT [Advanced Analog Technology, Inc.]

Applications Information
Input Capacitor
Typically, a 1µF or larger capacitor is recommend-
ed for C
not required for basic LDO regulator operation.
However, if the AAT3236 is physically located more
than six centimeters from an input power source, a
C
C
pin as practically possible. C
1µF will offer superior input line transient response
and will assist in maximizing the highest possible
power supply ripple rejection.
Ceramic, tantalum, or aluminum electrolytic capac-
itors may be selected for C
capacitor ESR requirement for C
300mA LDO regulator output operation, ceramic
capacitors are recommended for C
inherent capability over tantalum capacitors to with-
stand input current surges from low impedance
sources such as batteries in portable devices.
Output Capacitor
For proper load voltage regulation and operational
stability, a capacitor is required between pins V
and GND.
the LDO regulator ground pin should be made as
direct as practically possible for maximum device
performance.
The AAT3236 has been specifically designed to
function with very low ESR ceramic capacitors.
Although the device is intended to operate with
these low ESR capacitors, it is stable over a very
wide range of capacitor ESR, thus it will also work
with higher ESR tantalum or aluminum electrolytic
capacitors.
ceramic capacitors are recommended.
Typical output capacitor values for maximum out-
put current conditions range from 1µF to 10µF.
Applications utilizing the exceptionally low output
noise and optimum power supply ripple rejection
characteristics of the AAT3236 should use 2.2µF or
greater for C
increased without limit.
3236.2007.03.1.4
IN
IN
should be located as closely to the device V
capacitor will be needed for stable operation.
IN
in most applications. A C
The C
However, for best performance,
OUT
.
OUT
If desired, C
capacitor connection to
IN
IN
. There is no specific
values greater than
IN
. However, for
IN
IN
OUT
due to their
capacitor is
may be
OUT
IN
300mA CMOS High Performance LDO
In low output current applications where output
load is less than 10mA, the minimum value for
C
Bypass Capacitor and Low Noise
Applications
A bypass capacitor pin is provided to enhance the
very low noise characteristics of the AAT3236 LDO
regulator. The bypass capacitor is not necessary
for operation of the AAT3236. However, for best
device performance, a small ceramic capacitor
should be placed between the bypass pin (BYP)
and the device ground pin (GND). The value of
C
noise and best possible power supply ripple rejec-
tion performance a 10nF capacitor should be used.
To practically realize the highest power supply rip-
ple rejection and lowest output noise performance,
it is critical that the capacitor connection between
the BYP pin and GND pin be direct and PCB traces
should be as short as possible. Refer to the PCB
Layout Recommendations section of this datasheet
for examples.
There is a relationship between the bypass capac-
itor value and the LDO regulator turn-on time. In
applications where fast device turn-on time is
desired, the value of C
In applications where low noise performance
and/or ripple rejection are less of a concern, the
bypass capacitor may be omitted.
device turn-on time will be realized when no
bypass capacitor is used.
DC leakage on this pin can affect the LDO regula-
tor output noise and voltage regulation perform-
ance. For this reason, the use of a low leakage,
high quality ceramic (NPO or C0G type) or film
capacitor is highly recommended.
Capacitor Characteristics
Ceramic composition capacitors are highly recom-
mended over all other types of capacitors for use
with the AAT3236. Ceramic capacitors offer many
advantages over their tantalum and aluminum elec-
trolytic counterparts. A ceramic capacitor typically
has very low ESR, is lower cost, has a smaller PCB
OUT
BYP
can be as low as 0.47µF.
may range from 470pF to 10nF. For lowest
BYP
should be reduced.
AAT3236
The fastest
9