LTM8047 LINER [Linear Technology], LTM8047 Datasheet - Page 8

• Manufacturer Part Number: LTM8047
• Description: 3.1VIN to 32VIN Isolated ?Module DC/DC Converter
• Manufacturer: LINER [Linear Technology]

PIN FUNCTIONS
LTM8048
V
output of the LTM8048 flyback stage. Apply an external
capacitor between V
to exceed V
V
V
the LTM8048. In most applications, the bulk of the heat
flow out of the LTM8048 is through the GND and V
pads, so the printed circuit design has a large impact on
the thermal performance of the part. See the PCB Layout
and Thermal Considerations sections for more details.
Apply an external capacitor between V
V
post regulator. Apply the load and output capacitor between
V
for more information on output capacitance and reverse
output characteristics.
GND (Bank 4): This is the primary side local ground of the
LTM8048 primary. In most applications, the bulk of the heat
flow out of the LTM8048 is through the GND and V
pads, so the printed circuit design has a large impact on
the thermal performance of the part. See the PCB Layout
and Thermal Considerations sections for more details.
V
nal regulator and to the integrated power switch. These
pins must be locally bypassed with an external, low ESR
capacitor.
ADJ2 (pin A2): This is the input to the error amplifier of the
secondary side LDO post regulator. This pin is internally
clamped to ±7V. The ADJ2 pin voltage is 1.22V referenced
to V
ply a resistor from this pin to V
R
is not used, leave this pin floating.
8
OUT2
OUT1
OUT
OUT2
OUT2
IN
ADJ2
(Bank 5): V
OUT
–
. V
and V
(Bank 3): The output of the secondary side linear
= 608.78/(V
(Bank 1): V
(Bank 2): V
–
OUT1
and the output voltage range is 1.22V to 12V. Ap-
OUT1
OUT
and V
IN
–
.
. See the Applications Information section
supplies current to the LTM8048’s inter-
OUT1
OUT
OUT2
OUT
OUT1
–
–
and V
is the return for both V
– 1.22)kΩ. If the post regulator
comprise the isolated output of
and V
OUT
OUT
OUT
–
comprise the isolated
–
–
. Do not allow V
, using the equation
OUT1
and V
OUT1
OUT
OUT
OUT
OUT
–
and
.
–
–
–
BYP (Pin B2): The BYP pin is used to bypass the refer-
ence of the LDO to achieve low noise performance from
the linear post regulator. The BYP pin is clamped internally
to ±0.6V relative to V
to this pin will bypass the reference to lower the output
voltage noise. A maximum value of 0.01μF can be used
for reducing output voltage noise to a typical 20μV
over a 100Hz to 100kHz bandwidth. If not used, this pin
must be left unconnected.
RUN (Pin F3): A resistive divider connected to V
pin programs the minimum voltage at which the LTM8048
will operate. Below 1.24V, the LTM8048 does not deliver
power to the secondary. Above 1.24V, power will be de-
livered to the secondary and 10μA will be fed into the SS
pin. When RUN is less than 1.24V, the pin draws 2.5μA,
allowing for a programmable hysteresis. Do not allow a
negative voltage (relative to GND) on this pin.
ADJ1 (Pins G7): Apply a resistor from this pin to GND to
set the output voltage V
recommended value given in Table 1. If Table 1 does not
list the desired V
may be used to approximate the value. To the seasoned
designer, this exponential equation may seem unusual. The
equation is exponential due to non-linear current sources
that are used to temperature compensate the regulation.
BIAS (Pin H5): This pin supplies the power necessary to
operate the LTM8048. It must be locally bypassed with a
low ESR capacitor of at least 4.7μF . Do not allow this pin
voltage to rise above V
SS (Pin H6): Place a soft-start capacitor here to limit inrush
current and the output voltage ramp rate. Do not allow a
negative voltage (relative to GND) on this pin.
R
ADJ1
= 28.4 V
(
OUT1
OUT1
OUT
value, the equation
IN
–0.879
OUT1
–
.
. A small capacitor from V
relative to V
)
kΩ
OUT
–
, using the
IN
and this
OUT2
8048fa
RMS