ADUC814ARU-REEL Analog Devices, ADUC814ARU-REEL Datasheet - Page 60
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
ADUC814ARU-REEL
Manufacturer Part Number
ADUC814ARU-REEL
Description
MicroConverter/ Small Package 12-Bit ADC with Embedded Flash MCU
Manufacturer
Analog Devices
Datasheet
1.ADUC814ARU-REEL.pdf
(72 pages)
ADuC814
ADuC814 HARDWARE DESIGN CONSIDERATIONS
This section outlines some key hardware design considerations
for integrating the ADuC814 into any hardware system.
CLOCK OSCILLATOR
As described earlier, the core clock frequency for the ADuC814
is generated from an on-chip PLL that locks onto a multiple
(512 times) of 32.768 kHz. The latter is generated from an
internal clock oscillator. To use the internal clock oscillator,
connect a 32.768 kHz parallel resonant crystal between XTAL1
and XTAL2 pins (Pins 26 and 27) as shown in Figure 54.
As shown in the typical external crystal connection diagram in
Figure 54, two internal 12 pF capacitors are provided on-chip.
These are connected internally, directly to the XTAL1 and
XTAL2 pins. The total input capacitances at both pins is
detailed in the Specifications table. The value of the total load
capacitance required for the external crystal should be the value
recommended by the crystal manufacturer for use with that
specific crystal. In many cases, because of the on-chip capacitors,
additional external load capacitors are not required.
As an alternative to providing two separate power supplies,
AV
ferrite bead between it and DV
separately to ground. An example of this configuration is shown
in Figure 56. With this configuration, other analog circuitry
(such as op amps and voltage reference) can be powered from
the AV
POWER SUPPLIES
The ADuC814’s operational power supply voltage range is 2.7 V
to 5.5 V. Although the guaranteed data sheet specifications are
given only for power supplies within 2.7 V to 3.3 V or 4.5 V to
5.5 V, (±10% of the nominal level), the chip can function equally
well at any power supply level between 2.7 V and 5.5 V.
Users should separate analog and digital power supply pins
(AV
noisy digital signals often present on the system DV
this mode, the part can also operate with split supplies as long
as the supply voltages are within 0.3 V of each other. A typical
split-supply configuration is show in Figure 55.
DD
DD
can be kept quiet by placing a small series resistor and/or
DD
and DV
Figure 54. External Parallel Resonant Crystal Connections
supply line as well.
XTAL1
XTAL2
DD
) and allow AV
ADuC814
DD
DD
12pF
12pF
, and then decoupling AV
to be kept relatively free of
TO PLL
DD
line. In
DD
Rev. A | Page 60 of 72
Notice that in both Figure 55 and Figure 56, a large value
(10 µF) reservoir capacitor sits on DV
capacitor sits on AVDD. Also, local small-value (0.1 µF) capacitors
are located at each V
practice, be sure to include all of these capacitors, and ensure
that the smaller capacitors are closest to each AV
trace lengths as short as possible. Connect the ground terminal
of each of these capacitors directly to the underlying ground
plane. Finally, note that, at all times, the analog and digital ground
pins on the ADuC814 should be referenced to the same system
ground reference point.
POWER CONSUMPTION
The CORE values given represent the current drawn by DV
while the rest (ADC and DAC) are pulled by the AV
can be disabled in software when not in use. The other on-chip
peripherals (such as watchdog timer and power supply monitor)
consume negligible current and are therefore lumped in with
the CORE operating current here. Of course, the user must add
any currents sourced by the parallel and serial I/O pins, and that
sourced by the DAC, in order to determine the total current
needed at the ADuC814’s supply pins. Also, current drawn from
the DVDD supply increases by approximately 5 mA during the
Flash/EE erase and program cycles.
DIGITAL SUPPLY
DIGITAL SUPPLY
+
–
Figure 56. External Single-Supply Connections
Figure 55. External Dual-Supply Connections
0.1µF
+
–
0.1µF
10µF
DD
10µF
pin of the chip. As per standard design
DV
DGND
DD
DV
DGND
ADuC814
BEAD
DD
ADuC814
1.6Ω
AGND
AV
ANALOG SUPPLY
AGND
DD
DD
AV
10µF
DD
and a separate 10 µF
10µF
0.1µF
0.1µF
+
–
DD
pin with
DD
pin and
DD
,