HCPL-0710500 Agilent(Hewlett-Packard), HCPL-0710500 Datasheet
HCPL-0710500
Related parts for HCPL-0710500
HCPL-0710500 Summary of contents
Page 1
... OFF HCPL-0710 Basic building blocks of the HCPL-0710 are a CMOS LED driver IC, a high speed LED and a CMOS detector IC. A CMOS logic input signal controls the LED driver IC which supplies current to the LED. The detector IC incorporates an integrated photodiode, a high-speed transimpedance amplifier, and a voltage comparator with an output driver ...
Page 2
... Ordering Information Specify Part Number followed by Option Number (if desired) Example HCPL-0710#XXX Option data sheets available. Contact Hewlett-Packard sales representative or authorized distributor. Package Outline Drawing 8 3.937 ± 0.127 (0.155 ± 0.005) 1 PIN ONE 0.381 ± 0.076 (0.016 ± 0.003) 3.175 ± 0.127 (0.125 ± ...
Page 3
... Regulatory Information The HCPL-0710 has been approved by the following organizations: Insulation and Safety Related Specifications Parameter Minimum External Air Gap (Clearance) Minimum External Tracking (Creepage) Minimum Internal Plastic Gap (Internal Clearance) Tracking Resistance (Comparative Tracking Index) Isolation Group Absolute Maximum Ratings ...
Page 4
Electrical Specifications Test conditions that are not specified can be anywhere within the recommended operating range. All typical specifications are + Parameter Symbol DC Specifications Logic Low Input I DD1L Supply Current Logic High ...
Page 5
... Mimimum Pulse Width is the shortest pulse width at which 10% maximum, Pulse Width Distortion can be guaran- teed. Maximum Data Rate is the inverse of Minimum Pulse Width. Operating the HCPL-0710 at data rates above 12.5 MBd is possible provided PWD and data dependent jitter increases and relaxed noise margins 5 0 ° ...
Page 6
T (C) A Figure 4. Typical Pulse Width Distortion vs. Temperature PLH 21 T PHL ...
Page 7
... Application Information Bypassing and PC Board Layout The HCPL-0710 optocoupler is extremely easy to use. No external interface circuitry is required because the HCPL-0710 uses high-speed CMOS DD1 GND 0.01 µF TO 0.1 µF Figure 11. Recommended Printed Circuit Board Layout. V DD1 GND 1 Figure 12 ...
Page 8
... PWD (in ns) by the minimum pulse width (in ns) being trans- mitted. Typically, PWD on the order 30% of the minimum pulse width is tolerable. The PWD specification for the HCPL-0710 (10%) maximum across recommended operating condi- tions. 10% maximum is dictated by the most stringent of the three fieldbus standards, PROFIBUS ...
Page 9
... PSK t PSK uncertainty in the rest of the circuit does not cause a problem. The HCPL-0710 optocoupler offers the advantage of guaranteed specifications for propagation delays, pulse-width . distortion, and propagation delay skew over the recommended temperature and power supply ...
Page 10
... Isolation of nodes connected to any of the three types of digital field bus networks is best achieved by using the HCPL-0710 optocoupler. For each network, the HCPL-0710 satisifies the critical propagation delay and pulse width distortion require- ments over the temperature range +85 C, and power supply voltage range of 4 ...
Page 11
... Controller Area Network (CAN). Three types of isolated nodes are recommended for use on these networks: Isolated Node Powered NODE/APP SPECIFIC uP/CAN HCPL HCPL 0710 TRANSCEIVER DRAIN/SHIELD SIGNAL POWER NETWORK POWER SUPPLY Figure 18. Isolated Node Powered by the Network. ...
Page 12
... HCPL-0710 ensures the network will not “lock-up” if either AC line power to the node is lost or the node powered-off. Specifically, when input power ( the DD1 HCPL-0710 located in the transmit path is eliminated, a RECESSIVE bus state is ensured as the HCPL-0710 output voltage (V ) goes HIGH. O ...
Page 13
... HCPL-0710 ensures the network will not “lock-up” if either AC line power to the node is lost or the node powered-off. Specifically, when input power (V DD1 HCPL-0710 located in the transmit path is eliminated, a RECESSIVE bus state is ensured as the HCPL-0710 output voltage (V ) goes HIGH. O GALVANIC ISOLATION BOUNDARY V+ (SIGNAL) V– (SIGNAL) V+ (POWER) V– ...
Page 14
... Power Supplies and Bypassing The recommended DeviceNet application circuit is shown in Figure 21. Since the HCPL-0710 is fully compatible with CMOS logic level signals, the optocoup- ler is connected directly to the GALVANIC ISOLATION BOUNDARY ISO DD1 DD2 TX0 HCPL-0710 V 0.01 µF ...
Page 15
... Power Supplies and Bypassing The recommended PROFIBUS application circuit is shown in Figure 23. Since the HCPL-0710 is fully compatible with CMOS logic level signals, the optocoupler is connected directly to the transceiver. Two bypass capacitors (with values between 0.01 and 0.1 F) are required and should be located as close as possible to the input and output ...
Page 16
H For technical assistance or the location of your nearest Hewlett-Packard sales office, distributor or representative call: Americas/Canada: 1-800-235-0312 or 408-654-8675 Far East/Australasia: Call your local HP sales office. Japan: (81 3) 3335-8152 Europe: Call your local HP sales office. ...