HCPL063L Agilent, HCPL063L Datasheet

Page 1

... H A 0.1 µF bypass capacitor must be connected between pins 5 and 8. CAUTION advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD. Agilent HCPL-260L/ 060L/263L/063L High Speed LVTTL Compatible 3.3 Volt Optocouplers Data Sheet ...

Page 2

... BETWEEN PINS 5 AND 8 IS RECOMMENDED (SEE NOTE 5). Ordering Information Specify Part Number followed by Option Number (if desired). Example: HCPL-260L #XXX 060 = VDE 0884 V 500 = Tape and Reel Packaging Option Option data sheets available. Contact Agilent sales representative or authorized distributor for information ...

Page 3

Package Outline Drawings 8-Pin DIP Package 9.65 ± 0.25 (0.380 ± 0.010 TYPE NUMBER A XXXXZ YYWW 1 2 1.19 (0.047) MAX. 1.080 ± 0.320 (0.043 ± 0.013 OPTION CODE* DATE CODE ...

Page 4

Small Outline SO-8 Package 8 7 3.937 ± 0.127 (0.155 ± 0.005 PIN ONE 0.406 ± 0.076 (0.016 ± 0.003) 5.080 ± 0.127 * (0.200 ± 0.005) 3.175 ± 0.127 (0.125 ± 0.005) * TOTAL PACKAGE LENGTH (INCLUSIVE ...

Page 5

Insulation and Safety Related Specifications Parameter Symbol Minimum External Air L (101) Gap (External Clearance) Minimum External Tracking L (102) (External Creepage) Minimum Internal Plastic Gap (Internal Clearance) Minimum Internal Tracking (Internal Creepage) Tracking Resistance CTI (Comparative Tracking Index) Isolation ...

Page 6

Absolute Maximum Ratings (No Derating Required up to 85˚C) Parameter Storage Temperature Operating Temperature† Average Forward Input Current Reverse Input Voltage Input Power Dissipation Supply Voltage (1 Minute Maximum) Enable Input Voltage (Not to Exceed V by more than 500 ...

Page 7

... Input Reverse Breakdown BV R Voltage ∆V Input Diode Temperature / F ∆T Coefficient A Input Capacitance C IN *The JEDEC Registration specifies 0˚C to +70˚C. Agilent specifies –40˚C to +85˚C. = –40˚C to +85˚C) unless otherwise specified. All Typicals Min. Typ. Max. Units µA 4.5 50 3.0 5.0 mA 0.35 ...

Page 8

Switching Specifications Over Recommended Temperature ( 25˚ 3 Parameter Sym. Propagation Delay t PLH Time to High Output Level Propagation Delay t PHL Time to Low Output Level Pulse Width |t – ...

Page 9

... Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if applicable), your equipment level safety specification or Agilent Application Note 1074 entitled "Optocoupler Input-Output Endurance Voltage." Notes: 1 ...

Page 10

250 µ FOR SINGLE CHANNEL PRODUCTS ONLY 5 0 -60 -40 - – TEMPERATURE ...

Page 11

120 = 350 Ω PLH 350 Ω PHL -60 -40 - ...

Page 12

V BUS (FRONT Figure 11. Recommended printed circuit board layout. 3 CC1 220 Ω D1 – GND 1 1 *DIODE D1 (1N916 OR EQUIVALENT) IS NOT REQUIRED FOR UNITS WITH ...

Page 13

Application Information Common-Mode Rejection for HCPL-260L Families: Figure 13 shows the recom- mended drive circuit for optimal common-mode rejection performance. Two main points to note are: 1. The enable pin is tied rather than floating (this applies ...

Page 14

... Figure 17 may be used. The diode in parallel with the R speeds the turn-off LED of the optocoupler LED. www.semiconductor.agilent.com Data subject to change. Copyright © 2000 Agilent Technologies 5980-2523EN (11/00 420 Ω (MAX) 2N3906 74L504 (ANY PNP) (ANY ...