PEB3265 Infineon Technologies Corporation, PEB3265 Datasheet - Page 374
PEB3265
Manufacturer Part Number
PEB3265
Description
(PEB326x / PEB426x) Dual Channel Slicofi-2 / Slic Duslic
Manufacturer
Infineon Technologies Corporation
Datasheet
1.PEB3265.pdf
(383 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PEB3265F
Manufacturer:
INFINEON
Quantity:
111
Company:
Part Number:
PEB3265F V1.5
Manufacturer:
Infineon
Quantity:
853
Part Number:
PEB3265FV1.5
Manufacturer:
INFTEL
Quantity:
20 000
Company:
Part Number:
PEB3265H
Manufacturer:
Infineon
Quantity:
9
Company:
Part Number:
PEB3265H
Manufacturer:
SIEMENS
Quantity:
5 510
Company:
Part Number:
PEB3265H-V13
Manufacturer:
Infineon Technologies
Quantity:
10 000
Part Number:
PEB3265HV1.2
Manufacturer:
INFINEON/英飞凌
Quantity:
20 000
Part Number:
PEB3265HV1.3
Manufacturer:
INFINEON/英飞凌
Quantity:
20 000
Part Number:
PEB3265HV1.5
Manufacturer:
INF
Quantity:
20 000
- Current page: 374 of 383
- Download datasheet (6Mb)
Preliminary
8.3
• For each of the supply pins of SLICOFI-2x and SLIC, 100 nF capacitors should be
• SLICOFI-2x and SLIC should be placed as close to each other as possible.
• SLICOFI-2x and SLIC should be placed in such way that lines ACP, ACN, DCP, DCN,
• ACP/ACN lines should be placed parallel and symmetrical;
• DCP/DCN lines should be placed parallel and symmetrical;
• VCMITA and VCM should be connected directly (VCMITA via
• VCMITB and VCM should be connected directly (VCMITB via
• Use separate traces for connecting VCM/VCMITA and VCM/VCMITB
• In case of a multilayer board it is recommended to use one common ground layer
• In case of a two-layer board a common ground should be used for AGND, BGND,
• The connection of GND,
• Tip/ring traces from the SLIC should be symmetrical
Data Sheet
used. These capacitors should be placed as close as possible to the supply pin of the
associated ground/supply pins
IT, ITAC are as short as possible
via holes should be avoided
ACP/ACN lines should be run above a GND plane;
via holes should be avoided
DCP/DCN lines should be run above a GND plane
R
R
these two VCM traces should be connected directly at the VCM pin of SLICOFI-2x
(AGND, BGND, GNDD, GNDA, GNDB, GNDPLL connected together and share one
ground layer)
GNDD, GNDA, GNDB and GNDPLL. Ground traces should be layed out as large as
possible. Connections to and from groud pins should be as short as possible. Any
unused area of the board should be filled with ground (copper pouring)
impedance in order to avoid, e.g., a GND shift due to the high impulse currents in case
of an overvoltage strike.
IT2A
IT2B
(680 )
(680 )
DuSLIC Layout Recommendation
V
H
and
V
BAT
374
to the protection devices should be low-
Application Circuits
C
C
VCMITA
VCMITB
) at resistor
) at resistor
2000-07-14
DuSLIC
Related parts for PEB3265
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Antenna Switch Silicon Pin Diode
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Silicon Switching Diodes
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Single Igbt Driver Ic
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Igbt Modules
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
5 Volt Standard Regulator
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Active Biased Transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
N-channel Small Signal Mosfet 20v?800v
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Sipmos Small-signal Transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Complementary Mosfets 60v Small-signal-transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Complementary Mosfets 60v
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
P-channel Mosfets Power-transistor
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
N-channel Mosfet 20v?300v Power Transistor Power Mosfet
Manufacturer:
Infineon Technologies Corporation
Datasheet:
Part Number:
Description:
Power Mosfets
Manufacturer:
Infineon Technologies Corporation
Datasheet: