AM29F010B ETC, AM29F010B Datasheet - Page 3
![no-image](/images/no-image-200.jpg)
AM29F010B
Manufacturer Part Number
AM29F010B
Description
1 Megabit (128 K x 8-bit) CMOS 5.0 Volt-only/ Uniform Sector Flash Memory
Manufacturer
ETC
Datasheet
1.AM29F010B.pdf
(35 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AM29F010B
Manufacturer:
TI
Quantity:
5 510
Company:
Part Number:
AM29F010B-120FC
Manufacturer:
SPANSION
Quantity:
6 566
Company:
Part Number:
AM29F010B-120JC
Manufacturer:
AMD
Quantity:
6 100
Company:
Part Number:
AM29F010B-120JC
Manufacturer:
AMD
Quantity:
5
Part Number:
AM29F010B-120JC
Manufacturer:
AMD
Quantity:
20 000
Part Number:
AM29F010B-120JD
Manufacturer:
AMD
Quantity:
20 000
Part Number:
AM29F010B-120JI
Manufacturer:
AMD
Quantity:
20 000
Part Number:
AM29F010B-120PI
Manufacturer:
AMD
Quantity:
20 000
GENERAL DESCRIPTION
The Am29F010B is a 1 Mbit, 5.0 Volt-only Flash
memory organized as 131,072 bytes. The Am29F010B
is offered in 32-pin PDIP, PLCC and TSOP packages.
The byte-wide data appears on DQ0-DQ7. The de-
vice is designed to be programmed in-system with the
standard system 5.0 Volt V
required for program or erase operations. The device can
also be programmed or erased in standard EPROM
programmers.
This device is manufactured using AMD’s 0.32 µm pro-
cess technology, and offers all the features and benefits
of the Am29F010 and Am29F010A.
The standard device offers access times of 45, 55, 70,
90, and 120 ns, allowing high-speed microprocessors
to operate without wait states. To eliminate bus conten-
tion the device has separate chip enable (CE#), write
enable (WE#) and output enable (OE#) controls.
The device requires only a single 5.0 volt power sup-
ply for both read and write functions. Internally
generated and regulated voltages are provided for the
program and erase operations.
The device is entirely command set compatible with the
JEDEC single-power-supply Flash standard. Com-
mands are written to the command register using
standard microprocessor write timings. Register con-
tents serve as input to an internal state machine that
controls the erase and programming circuitry. Write
cycles also internally latch addresses and data needed
for the programming and erase operations. Reading
data out of the device is similar to reading from other
Flash or EPROM devices.
Device programming occurs by executing the program
command sequence. This invokes the Embedded
Program algorithm—an internal algorithm that auto-
2
CC
supply. A 12.0 volt V
PP
is not
Am29F010B
matically times the program pulse widths and verifies
proper cell margin.
Device erasure occurs by executing the erase com-
mand sequence. This invokes the Embedded Erase
algorithm—an internal algorithm that automatically pre-
programs the array (if it is not already programmed)
before executing the erase operation. During erase,
the device automatically times the erase pulse widths
and verifies proper cell margin.
The host system can detect whether a program or
erase operation is complete by reading the DQ7 (Data#
Polling) and DQ6 (toggle) status bits. After a program
or erase cycle has been completed, the device is ready
to read array data or accept another command.
The sector erase architecture allows memory sectors
to be erased and reprogrammed without affecting the
data contents of other sectors. The device is erased
when shipped from the factory.
The hardware data protection measures include a
low V
during power transitions. The hardware sector protec-
tion feature disables both program and erase
operations in any combination of the sectors of memory,
a n d i s i m p l e m e n t e d u s i n g s t a n d a r d E P R O M
programmers.
The system can place the device into the standby mode.
Power consumption is greatly reduced in this mode.
AMD’s Flash technology combines years of Flash
memory manufacturing experience to produce the
hi gh es t le ve l s o f q ua li ty, r e li ab i li ty, a nd c os t
effectiveness. The device electrically erases all bits
within a sector simultaneously via Fowler-Nordheim
tunneling. The bytes are programmed one byte at a
time using the EPROM programming mechanism of
hot electron injection.
CC
detector automatically inhibits write operations
November 18, 2002