SMM153_10 SUMMIT [Summit Microelectronics, Inc.], SMM153_10 Datasheet - Page 8

• Manufacturer Part Number: SMM153_10
• Description: 10-bit Digital Differential Voltage and Current Monitor
• Manufacturer: SUMMIT [Summit Microelectronics, Inc.]

DEVICE OPERATION
POWER SUPPLY
The SMM153 can be powered by a 2.7V to 5.5V input
to the VDD pin (Figure 1). See Figure 4 as an
example.
VOLTAGE REFERENCE
The SMM153 uses an internal voltage reference,
VREF of 1.25V. Total accuracy of VREF is ±1.0% over
temperature and supply variations.
MODES OF OPERATION
The SMM153 has three basic modes of operation:
UV/OV monitoring, differential output voltage sensing
and input current measuring mode. A detailed
description of each mode and feature follows and can
also be found in Application Note 68.
MONITOR
The SMM153 monitors the COMP1 and COMP2 pins.
COMP1 and COMP2 are high impedance inputs, each
connected internally to a comparator and compared
against the programmable internal reference voltage.
Each comparator can be independently programmed
to monitor for either an under-voltage (UV) or an over-
voltage (OV. The monitor level may be set externally
with a resistive voltage divider. The COMPx pins can
be connected to Vin, Vout or any voltage that needs to
be monitored. The internal comparators COMP1/2 are
compared to VREF, so the voltage dividers are set
above or below the programmed VREF level
depending on whether monitoring UV or OV. As an
example, with VREF set to 1.25V, to monitor an OV of
1.7V on COMP1 and a UV of 1.3V on COMP2, the
voltage divider resistors are:
For OV, RUpper = 1.37k, 1% RLower = 3.83k, 1%.
For UV, RUpper = 1.02k, 1% RLower = 25.5k, 1%.
The part can be programmed to trigger the FAULT#
pin when either COMPx comparator has exceeded the
UV or OV setting. The FAULT# output of the SMM153
is active as long as the triggering limit remains in a
fault condition. When either of the COMP1 or COMP2
inputs are in fault, the open-drain FAULT# output will
be pulled low.
GENERAL-PURPOSE INPUTS/OUTPUTS
The four integrated GPIOs are open drain type
outputs. The pins should be pulled up externally to
voltages ranging from 2.0V to 12V. Each I/O has Non-
volatile memory setting associated with it that
determines the power-on state of the pin. The status
(High/Low) is read from bit 0 of registers 34h, 35h, 36h
or 37h with 0=Low and 1=High. Additionally, the I/Os
have a command bit that when written overrides the
Summit Microelectronics, Inc
APPLICATIONS INFORMATION
2134 3.0 1/20/2010
8
NV setting and sets the pin either high or low. The I/Os
also have status bits to read the state of the pin as
high or low. The command/status register for each I/O
is addressed separately alleviating the need for the
host controller to remember the state of the other I/Os
when writing commands. More information can be
found in Application Note 69.
STATUS REGISTER
A status register exists for I
the COMP1 and COMP2 inputs. Two bits in this status
register reflect the current state of the inputs (1 = fault,
0 = no fault). Two additional bits show the state of the
inputs latched by the FAULT# event (i.e. FAULT#
output going active) programmed in the configuration.
More information can be found in Application Note 69.
FAULTS
When either of the COMP1 or COMP2 inputs are in
fault, the open-drain FAULT# output will be pulled low.
The FAULT# is triggered only on the leading edge of a
Fault. That is, a latched fault can be cleared while the
Fault yet exists.
WRITE PROTECTION
Write protection for the SMM153 is located in a volatile
register where the power-on state is defaulted to write
protect. There are separate write protect modes for the
configuration registers and memory. In order to
remove write protection, the code 55
the write protection register.
Other codes will enable write protection. For example,
writing 59
register but not to the memory, while writing 35
allow writes to the memory but not to the configuration
registers. The SMM153 also features a Write Protect
pin (WP input) which, when asserted, prevents writing
to the configuration registers and EE memory. In
addition to these two forms of write protection there is
a
programmed,
registers to be changed.
A2, A1, A0
The address bits A[2:0] can be hard wired High or Low
or may be left open (High-Z) to allow for a total of 21
distinct device addresses. When floating, the inputs
can tolerate the amount of leakage as described by
the specification I
down resistor is sufficient to set a High or Low logic
level.
configuration
HEX
will allow writes to the configuration
does
AIT
register
. An external 100k pull-up or pull
not
2
allow
C polling of the status of
lock
bit
the
SMM153
HEX
which,
configuration
is written to
HEX
once
will