M74LCX16373DTR2G ON Semiconductor, M74LCX16373DTR2G Datasheet - Page 7

• Manufacturer Part Number: M74LCX16373DTR2G
• Description: IC LATCH TRANSP 16BIT 48-TSSOP
• Manufacturer: ON Semiconductor
• Series: 74LCXr
• Type: D-Typer

Specifications of M74LCX16373DTR2G

• Logic Type: D-Type Transparent Latch
• Circuit: 8:8
• Output Type: Tri-State
• Voltage - Supply: 2 V ~ 3.6 V
• Independent Circuits: 2
• Delay Time - Propagation: 1.5ns
• Current - Output High, Low: 24mA, 24mA
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 48-TSSOP
• Logic Family: LCX
• Number Of Bits: 16
• Number Of Elements: 2
• Latch Mode: Transparent
• Polarity: Non-Inverting
• Technology: CMOS
• Package Type: TSSOP
• Propagation Delay Time: 7.9ns
• Operating Supply Voltage (typ): 2.5/3.3V
• High Level Output Current: -24mA
• Low Level Output Current: 24mA
• Operating Supply Voltage (min): 2V
• Operating Supply Voltage (max): 3.6V
• Operating Temp Range: -55C to 125C
• Operating Temperature Classification: Military
• Mounting: Surface Mount
• Pin Count: 48
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [e-mail]
−T−
ON Semiconductor and
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
0.076 (0.003)
SEATING
PLANE
PIN 1
IDENT.
D
L
C
48
1
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
48X
K
0.12 (0.005)
REF
−V−
A
G
M
1
T
U
0.32
48X
N. American Technical Support: 800−282−9855 Toll Free
Europe, Middle East and Africa Technical Support:
Japan Customer Focus Center
S
PACKAGE DIMENSIONS
USA/Canada
Phone: [phone]
Phone: 81−3−5773−3850
SOLDERING FOOTPRINT
V
http://onsemi.com
S
25
24
CASE 1201−01
RECOMMENDED
TSSOP−48
−U−
ISSUE B
B
H
7
N
J
DETAIL E
DETAIL E
N
0.50
PITCH
J1
SECTION N−N
Ç Ç Ç
É É É
Ç Ç Ç
É É É
Ç Ç Ç
É É É
F
K1
K
DIMENSIONS: MILLIMETERS
0.25 (0.010)
M
−W−
1.00
48X
NOTES:
1. DIMENSIONING AND TOLERANCING PER
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSIONS A AND B DO NOT INCLUDE
4. DIMENSION K DOES NOT INCLUDE DAMBAR
5. TERMINAL NUMBERS ARE SHOWN FOR
6. DIMENSIONS A AND B ARE TO BE
8.45
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
ANSI Y14.5M, 1982.
MOLD FLASH, PROTRUSIONS OR GATE
BURRS. MOLD FLASH OR GATE BURRS
SHALL NOT EXCEED 0.15 (0.006) PER SIDE.
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL
IN EXCESS OF THE K DIMENSION AT
MAXIMUM MATERIAL CONDITION.
REFERENCE ONLY.
DETERMINED AT DATUM PLANE −W−.
DIM
K1
J1
M
A
B
C
D
G
H
K
F
J
L
12.40
MILLIMETERS
MIN
6.00
0.05
0.50
0.37
0.09
0.09
0.17
0.17
7.95
−−−
0.50 BSC
0
_
12.60
MAX
6.20
1.10
0.15
0.75
0.20
0.16
0.27
0.23
8.25
MC74LCX16373/D
−−−
8
_
0.488
0.236
0.002
0.020
0.015
0.004
0.004
0.007
0.007
0.313
MIN
0.0197 BSC
−−−
0
INCHES
_
0.496
0.244
0.043
0.006
0.030
0.008
0.006
0.009
0.325
MAX
0.011
−−−
8
_