74HC423D,653 NXP Semiconductors, 74HC423D,653 Datasheet - Page 10

• Manufacturer Part Number: 74HC423D,653
• Description: IC MULTIVIBRATR DUAL MONO 16SOIC
• Manufacturer: NXP Semiconductors
• Series: 74HCr

Specifications of 74HC423D,653

• Logic Type: Monostable
• Package / Case: 16-SOIC (3.9mm Width)
• Independent Circuits: 2
• Schmitt Trigger Input: Yes
• Propagation Delay: 20ns
• Current - Output High, Low: 5.2mA, 5.2mA
• Voltage - Supply: 2 V ~ 6 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Elements Per Chip: 2
• Logic Family: HC
• Input Bias Current (max): 0.008 mA
• Propagation Delay Time: 255 ns, 51 ns, 43 ns
• High Level Output Current: - 5.2 mA
• Low Level Output Current: 5.2 mA
• Supply Voltage (max): 6 V
• Supply Voltage (min): 2 V
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 5 V
• Quiescent Current: 8nA
• Number Of Elements: 2
• Operating Temperature Classification: Automotive
• Operating Supply Voltage (max): 6V
• Operating Supply Voltage (typ): 5V
• Operating Temperature (min): -40C
• Operating Temperature (max): 125C
• Technology: CMOS
• Abs. Propagation Delay Time: 385ns
• Operating Supply Voltage (min): 2V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 74HC423D-T; 74HC423D-T; 933714870653

NXP Semiconductors
Table 7.
GND = 0 V; test circuit see
[1]
[2]
[3]
[4]
[5]
[6]
74HC_HCT423
Product data sheet
Symbol Parameter
C
PD
t
t
For other R
t
t
R
C
K = 0.55 for V
Inherent test jig and pin capacitance at pins 15 and 7 (nREXT/CEXT) is 7 pF.
The time to retrigger the monostable multivibrator depends on the values of R
extended when the time between the active-going edges of the trigger input pulses meets the minimum retrigger time.
If C
t
t
C
R
Inherent test jig and pin capacitance at pins 15 and 7 (nREXT/CEXT) is 7 pF.
When the device is powered-up, initiate the device via a reset pulse, when C
C
P
f
f
C
V
N = number of inputs switching;
Σ(C
pd
t
W
W
rtrig
rtrig
i
o
D
CC
EXT
EXT
EXT
EXT
PD
L
is the same as t
= input frequency in MHz;
= output frequency in MHz;
= K × R
= output pulse width in ns;
is the same as t
= output load capacitance in pF;
= C
EXT
L
= retrigger time in ns;
= 30 + 0.19 × R
is used to determine the dynamic power dissipation (P
= supply voltage in V;
× V
= external resistor in kΩ;
= external capacitor in pF;
= external capacitor in pF;
= external resistor in kΩ.
power
dissipation
capacitance
PD
> 10 pF, the next formula (at V
Dynamic characteristics
CC
× V
EXT
2
EXT
× f
CC
CC
× C
o
and C
2
) = sum of outputs.
= 2.0 V and 0.45 for V
× f
THL
EXT
PHL
EXT
i
× N + Σ(C
and t
EXT
(typ.), where:
and t
× C
Conditions
per package; V
combinations see
Figure
TLH
EXT
PLH
.
0.9
L
.
× V
12.
+ 13 × R
CC
CC
2
…continued
CC
× f
= 5.0 V) for the set-up time of a retrigger pulse is valid:
I
= 5.0 V; see
EXT
o
All information provided in this document is subject to legal disclaimers.
); where:
= GND to V
Figure
1.05
(typ.); where:
8. If C
Rev. 4 — 18 March 2011
Figure
CC
EXT
D
− 1.5 V
in μW):
> 10 pF, the next formula is valid:
9.
Dual retriggerable monostable multivibrator with reset
[6]
EXT
EXT
Min
74HC423; 74HCT423
< 50 pF.
-
and C
25 °C
Typ
56
EXT
. The output pulse width will only be
Max Min Max Min Max
-
−40 °C to
+85 °C
-
-
© NXP B.V. 2011. All rights reserved.
−40 °C to
+125 °C
-
-
10 of 24
Unit
pF