CBTU4411EE,551 NXP Semiconductors, CBTU4411EE,551 Datasheet
CBTU4411EE,551
Specifications of CBTU4411EE,551
CBTU4411EE-S
CBTU4411EE-S
Available stocks
Related parts for CBTU4411EE,551
CBTU4411EE,551 Summary of contents
Page 1
CBTU4411 11-bit DDR2 SDRAM MUX/bus switch with 12 Rev. 03 — 12 October 2009 1. General description This 11-bit bus switch is designed for 1 1 input levels. Each Host port pin (HPn) is multiplexed to ...
Page 2
... NXP Semiconductors 2. Features I Enable (EN) and select signals (S0, S1) are SSTL_18 compatible I Optimized for use in Double Data Rate 2 (DDR2) SDRAM applications I Suitable to be used with 400 Mbit/s to 800 Mbit/s, 200 MHz to 400 MHz DDR2 data bus I Switch ON-resistance is designed to eliminate the need for series resistor to DDR2 ...
Page 3
... NXP Semiconductors 4. Functional diagram VREF TERM STREN (1) Selectable. Fig 1. HPn A from switch control Fig 2. CBTU4411_3 Product data sheet 11-bit DDR2 SDRAM MUX/bus switch with 12 HP0 HP10 (1) ( (1) ( CONTROL Functional diagram (positive logic xDPn SWITCH 400 VBIAS 002aae848 Simplified schematic, channel 0 to channel 9 Rev. 03 — ...
Page 4
... NXP Semiconductors 5. Pinning information 5.1 Pinning Fig Fig 5. CBTU4411_3 Product data sheet 11-bit DDR2 SDRAM MUX/bus switch with 12 ball A1 index area Pin configuration STREN V 0DP0 1DP0 DD TERM S0 V GND HP0 DD VREF EN VBIAS GND 2DP10 3DP10 1DP10 HP10 0DP10 GND 3DP9 ...
Page 5
... NXP Semiconductors 5.2 Pin description Table 2. Symbol HP0 to HP10 EN STREN S0 S1 VREF VBIAS TERM 0DP0, 1DP0, 2DP0, 3DP0 0DP1, 1DP1, 2DP1, 3DP1 0DP2, 1DP2, 2DP2, 3DP2 0DP3, 1DP3, 2DP3, 3DP3 0DP4, 1DP4, 2DP4, 3DP4 0DP5, 1DP5, 2DP5, 3DP5 0DP6, 1DP6, 2DP6, 3DP6 ...
Page 6
... NXP Semiconductors 6. Functional description Refer to 6.1 Function selection Table 3. Function selection, channel 0 to channel HIGH voltage level LOW voltage level; high-Z = high-impedance Don’t care. Inputs HPn high high high high-Z CBTU4411_3 Product data sheet 11-bit DDR2 SDRAM MUX/bus switch with 12 Figure 1 “ ...
Page 7
Table 4. Function selection, channel HIGH voltage level LOW voltage level; high-Z = high-impedance Don’t care. Inputs 0DP10 STREN HP10 VBIAS high ...
Page 8
... NXP Semiconductors 7. Limiting values Table 6. In accordance with the Absolute Maximum Rating System (IEC 60134). The package thermal impedance is calculated in accordance with JESD 51. Symbol stg [1] The input and output negative voltage ratings may be exceeded if the input and output clamping current ratings are observed. ...
Page 9
... NXP Semiconductors 9. Static characteristics Table 8. Static characteristics +85 C amb Symbol Parameter V input clamping voltage IK V termination voltage T V pull-up voltage pu I input leakage current LI I supply current DD C input capacitance in C switch on capacitance resistance resistance ON mismatch between channels R pull-down resistance pd R pull-up resistance ...
Page 10
... NXP Semiconductors Fig 6. 10. Dynamic characteristics Table 9. Dynamic characteristics V = 1 Symbol Parameter t propagation delay PD t driver enable delay to HIGH level PZH t driver enable delay to LOW level PZL t driver disable delay from HIGH level from Sn to HPn or xDPn PHZ t driver disable delay from LOW level from Sn to HPn or xDPn ...
Page 11
... NXP Semiconductors 11. HPn to xDPn AC waveforms and test circuit Fig 7. (1) See (2) Waveform 1 is for an output with internal conditions such that the output is HIGH except when Fig 8. Fig 9. CBTU4411_3 Product data sheet 11-bit DDR2 SDRAM MUX/bus switch with 12 input 0 PLH output Input to output propagation delays ...
Page 12
... NXP Semiconductors 12. xDPn to HPn AC waveforms and test circuit (1) See (2) Waveform 1 is for an output with internal conditions such that the output is LOW except when (3) Waveform 2 is for an output with internal conditions such that the output is HIGH except when Fig 10. 3-state output enable and disable times Fig 11 ...
Page 13
... NXP Semiconductors Fig 13. Test circuit (xDPn to HPn) 13. Test information Table 10. Condition bias V < 0.5V bias CBTU4411_3 Product data sheet 11-bit DDR2 SDRAM MUX/bus switch with HPn 2.54 cm (1") SSTL_18 driver All input pulses are supplied by generators having the following characteristics: PRR 10 MHz ...
Page 14
... NXP Semiconductors 14. Package outline LFBGA72: plastic low profile fine-pitch ball grid array package; 72 balls; body 1.05 mm ball A1 index area ball A1 index area DIMENSIONS (mm are the original dimensions) A UNIT max 0.3 1.20 0.35 mm 1.5 0.2 0.95 0.25 OUTLINE VERSION IEC SOT856-1 Fig 14. Package outline SOT856-1 (LFBGA72) ...
Page 15
... NXP Semiconductors 15. Soldering of SMD packages This text provides a very brief insight into a complex technology. A more in-depth account of soldering ICs can be found in Application Note AN10365 “Surface mount reflow soldering description” . 15.1 Introduction to soldering Soldering is one of the most common methods through which packages are attached to Printed Circuit Boards (PCBs), to form electrical circuits ...
Page 16
... NXP Semiconductors 15.4 Reflow soldering Key characteristics in reflow soldering are: • Lead-free versus SnPb soldering; note that a lead-free reflow process usually leads to higher minimum peak temperatures (see reducing the process window • Solder paste printing issues including smearing, release, and adjusting the process window for a mix of large and small components on one board • ...
Page 17
... NXP Semiconductors Fig 15. Temperature profiles for large and small components For further information on temperature profiles, refer to Application Note AN10365 “Surface mount reflow soldering description” . 16. Abbreviations Table 13. Acronym CDM DDR2 DIMM DQM ESD HBM LVCMOS MM MUX PRR RC SDRAM SSTL_18 ...
Page 18
... CBTU4411_3 20091012 • Modifications: The format of this data sheet has been redesigned to comply with the new identity guidelines of NXP Semiconductors. • Legal texts have been adapted to the new company name where appropriate. • Section 2 667 Mbit/s, 200 MHz to 333 MHz DDR2 data bus” to “Suitable to be used with 400 Mbit/s to 800 Mbit/s, 200 MHz to 400 MHz DDR2 data bus” ...
Page 19
... Right to make changes — NXP Semiconductors reserves the right to make changes to information published in this document, including without limitation specifications and product descriptions, at any time and without notice ...
Page 20
... NXP Semiconductors 20. Contents 1 General description . . . . . . . . . . . . . . . . . . . . . . 1 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 3 Ordering information . . . . . . . . . . . . . . . . . . . . . 2 4 Functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 5 Pinning information . . . . . . . . . . . . . . . . . . . . . . 4 5.1 Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 5.2 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 5 6 Functional description . . . . . . . . . . . . . . . . . . . 6 6.1 Function selection Limiting values Recommended operating conditions Static characteristics Dynamic characteristics . . . . . . . . . . . . . . . . . 10 11 HPn to xDPn AC waveforms and test circuit . 11 12 xDPn to HPn AC waveforms and test circuit ...