M470T2864AZ3-CLE6/D5/CC SAMSUNG [Samsung semiconductor], M470T2864AZ3-CLE6/D5/CC Datasheet - Page 10

• Manufacturer Part Number: M470T2864AZ3-CLE6/D5/CC
• Description: DDR2 Unbuffered SODIMM 200pin Unbuffered SODIMM based on 1Gb A-die 64-bit Non-ECC
• Manufacturer: SAMSUNG [Samsung semiconductor]

8.0 Absolute Maximum DC Ratings
Note :
1. Stresses greater than those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and
2. Storage Temperature is the case surface temperature on the center/top side of the DRAM. For the measurement conditions, please refer to JESD51-2
9.0 AC & DC Operating Conditions
9.1 Recommended DC Operating Conditions (SSTL - 1.8)
Note : There is no specific device V
1. The value of V
2. Peak to peak AC noise on V
3. V
4. AC parameters are measured with V
5. SO-DIMMs that include an optional temperature sensor may require a restricted V
SODIMM
functional operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Exposure to absolute maximum rating conditions for extended periods may affect reliability.
standard.
x V
sensor. Refer to the thermal sensor specification for details regarding the supported voltage range. All other functions of the SO-DIMM SPD are
supported across the full V
V
TT
Symbol
V
Symbol
Symbol
IN,
V
DDQ
V
T
V
DD
V
V
to V
V
V
V
of transmitting device must track V
DDQ
STG
DDL
DDQ
DDL
REF
V
DD
DD
TT
SPD
OUT
of the transmitting device and V
DD
.
REF
Voltage on V
Voltage on V
Voltage on V
Voltage on any pin relative to V
Storage Temperature
Supply Voltage
Supply Voltage for DLL
Supply Voltage for Output
Input Reference Voltage
Termination Voltage
Core Supply Voltage
may be selected by the user to provide optimum noise margin in the system. Typically the value of V
DD
DD
DDQ
DDL
REF
SPD range.
pin relative to V
pin relative to V
DD
pin relative to V
may not exceed +/-2% V
Parameter
Parameter
supply voltage requirement for SSTL-1.8 compliance. However under all conditions V
DD
Parameter
REF
, V
REF
DDQ
of receiving device.
is expected to track variations in V
SS
SS
and V
SS
SS
DDL
tied together.
REF
(DC).
0.49*V
V
REF
Min.
10 of 20
1.7
1.7
1.7
-0.04
DDQ
Min.
1.7
DDQ
DD
.
SPD operating voltage range for proper operation of the temperature
0.50*V
Rating
Rating
V
Typ.
1.8
1.8
1.8
REF
DDQ
- 1.0 V ~ 2.3 V
- 0.5 V ~ 2.3 V
- 0.5 V ~ 2.3 V
- 0.5 V ~ 2.3 V
-55 to +100
Rating
Max.
3.6
0.51*V
V
REF
Max.
1.9
1.9
1.9
+0.04
DDQ
REF
Rev. 1.4 March 2007
DDQ
DDR2 SDRAM
Units
Units
mV
is expected to be about 0.5
V
V
V
V
V
must be less than or equal
Units
°C
V
V
V
V
Notes
Notes
1,2
Notes
4
4
3
5
1, 2
1
1
1
1