ISL6549 INTERSIL [Intersil Corporation], ISL6549 Datasheet - Page 16
![no-image](/images/no-image-200.jpg)
ISL6549
Manufacturer Part Number
ISL6549
Description
Single 12V Input Supply Dual Regulator Synchronous Rectified Buck PWM and Linear Power Controller
Manufacturer
INTERSIL [Intersil Corporation]
Datasheet
1.ISL6549.pdf
(18 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ISL6549CAZ
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
ISL6549CAZA
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
ISL6549CAZA-T
Manufacturer:
INTERSIL
Quantity:
20 000
Company:
Part Number:
ISL6549CB
Manufacturer:
Intersil
Quantity:
490
Company:
Part Number:
ISL6549CB-T
Manufacturer:
INTERSIL
Quantity:
2 299
Part Number:
ISL6549CB-T
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
ISL6549CBZ
Manufacturer:
INTERSIL
Quantity:
20 000
Company:
Part Number:
ISL6549CRZ
Manufacturer:
Intersil
Quantity:
9 000
Company:
Part Number:
ISL6549IBZ-T
Manufacturer:
ROHM
Quantity:
8 122
Quad Flat No-Lead Plastic Package (QFN)
Micro Lead Frame Plastic Package (MLFP)
16
ISL6549
L16.4x4
16 LEAD QUAD FLAT NO-LEAD PLASTIC PACKAGE
(COMPLIANT TO JEDEC MO-220-VGGC ISSUE C)
NOTES:
10. Depending on the method of lead termination at the edge of the
1. Dimensioning and tolerancing conform to ASME Y14.5-1994.
2. N is the number of terminals.
3. Nd and Ne refer to the number of terminals on each D and E.
4. All dimensions are in millimeters. Angles are in degrees.
5. Dimension b applies to the metallized terminal and is measured
6. The configuration of the pin #1 identifier is optional, but must be
7. Dimensions D2 and E2 are for the exposed pads which provide
8. Nominal dimensions are provided to assist with PCB Land Pattern
9. Features and dimensions A2, A3, D1, E1, P & θ are present when
SYMBOL
between 0.15mm and 0.30mm from the terminal tip.
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
improved electrical and thermal performance.
Design efforts, see Intersil Technical Brief TB389.
Anvil singulation method is used and not present for saw
singulation.
package, a maximum 0.15mm pull back (L1) maybe present. L
minus L1 to be equal to or greater than 0.3mm.
A1
A2
A3
D1
D2
E1
E2
Nd
Ne
L1
A
D
E
N
P
b
e
k
L
θ
0.80
0.23
1.95
1.95
0.25
0.50
MIN
-
-
-
-
-
MILLIMETERS
NOMINAL
4.00 BSC
3.75 BSC
4.00 BSC
3.75 BSC
0.20 REF
0.65 BSC
0.90
0.28
2.10
2.10
0.60
16
4
4
-
-
-
-
-
-
MAX
1.00
0.05
1.00
0.35
2.25
2.25
0.75
0.15
0.60
12
-
September 22, 2006
Rev. 5 5/04
NOTES
FN9168.2
5, 8
7, 8
7, 8
10
9
9
9
9
8
2
3
3
9
9
-
-
-
-
-
-