W6691CD WINBOND [Winbond], W6691CD Datasheet - Page 40
W6691CD
Manufacturer Part Number
W6691CD
Description
ISDN S/T Interface Transceiver
Manufacturer
WINBOND [Winbond]
Datasheet
1.W6691CD.pdf
(106 pages)
- Current page: 40 of 106
- Download datasheet (466Kb)
7.2.8Test Functions
The W6691 provides loop and test functions as follows:
-
-
-
-
Digital loop via DLP bit in D_MODE register: In the layer 2 block, the transmitted 2B+D data are
internally looped (from HDLC transmitter to HDLC receiver), and in the PCM ports, the
transmitted B channels are internally looped (from PCM inputs to PCM outputs). The clock
timings are generated internally and are independent of the S bus timing. This loop function is
used for test of PCM and higher layer functions, excluding layer 1. After hardware reset, W6691
will power down if S bus is not connected or if there is no signal on the S bus. In this case, the
C/I command ECK must be issued to power up the chip.
Analog loop via the C/I command EAL: The analog S interface transmitter is internally
connected to the S interface receiver. When the receiver has synchronized itself to the internal
INFO 3 signal, the message "Test Indication" or "Awake Test Indication" is delivered to the CIR
register. No signal is transmitted over the S interface.
In this mode, the S interface awake detector is enabled. Therefore if a level (INFO 2/ INFO 4) is
detected on the S interface, this will be reported by the "Awake Test Indication (ATI)" indication.
Remote loopback via RLP bit in D_MODE register: The digital 2B data received from the S
interface receiver is loopbacked to the S interface transmitter. The D channel is not looped.
When RLP is enabled, layer 1 D channel is connected to HDLC port and DLP cannot be
enabled.
Transmission of special test signals via layer 1 command:
* Send Single Pulses (SSP): To send isolated single pulses of alternating polarity, with pulse
width of one bit time, 250 us apart, with a repetition frequency of 2 kHz.
* Send Continuous Pulses (SCP): To send continuous pulses of alternating polarity, with pulse
width of bit time. The repetition frequency is 96 kHz.
40
Preliminary W6691
Publication Release Date: Sep 2001
Revision 1.1
Related parts for W6691CD
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Isdn S/t Interface Transceiver
Manufacturer:
Winbond Electronics Corp America
Datasheet:
Part Number:
Description:
WINBOND I/O, UART, infrared, parallel port, game port, MIDI port, flash ROM interface, general purpose I/O ports, FDC, hardware monitor functions
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
13-MEMORY TONE/PULSE DIALER WITH SAVE FUNCTION
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
TOUCH PULSE DIALER WITH REDIAL
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
Tone/pulse dialer with redial function
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
TOUCH PULSE DIALER WITH REDIAL
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
DTMF Transmitter, 3.58MHz, 5V, Standby, CMOS, 18-PDIP
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
SERIAL VOICE SRAM (128K 1 BIT)
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
DTMF Transmitter, 3.58MHz, 5V, Standby, CMOS, 18-PDIP
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
13-MEMORY TONE/PULSE DIALER WITH SAVE FUNCTION
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
WE9142ATone/Pulse Telephone Dialer
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
13 Memory Tone / Pulse Switchable Dialer with Save Function
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
14-memory tone/pulse switchable dialer with handfree and lock functions
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
10-memory tone/pulse dialer with save function
Manufacturer:
Winbond
Datasheet:
Part Number:
Description:
23-flash memory tone/pulse dialer with handfree, lock and hold functions
Manufacturer:
Winbond
Datasheet: