AX88796BLI ASIX [ASIX Electronics Corporation], AX88796BLI Datasheet - Page 12
![no-image](/images/no-image-200.jpg)
AX88796BLI
Manufacturer Part Number
AX88796BLI
Description
Low-pin-count Non-PCI 8/16-bit 10/100M Fast Ethernet Controller
Manufacturer
ASIX [ASIX Electronics Corporation]
Datasheet
1.AX88796BLI.pdf
(82 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AX88796BLI
Manufacturer:
ASIX
Quantity:
20 000
4.0 Basic Operation
4.1 Receiver Filtering
MAR0
MAR1
MAR2
MAR3
MAR4
MAR5
MAR6
MAR7
PAR0
PAR1
PAR2
PAR3
PAR4
PAR5
4.1.1 Unicast Address Match Filter
4.1.2 Multicast Address Match Filter
The address filtering logic compares the Destination Address Field (first 6 bytes of the received packet) to the
Physical address registers stored in the Address Register Array. If any one of the six bytes does not match the
pre-programmed physical address, the Protocol Control Logic rejects the packet. This is for unicast address filtering.
All multicast destination addresses are filtered using a hashing algorithm. (See following description.) If the
multicast address indexes a bit that has been set in the filter bit array of the Multicast Address Register Array the
packet is accepted, otherwise the Protocol Control Logic rejects it. Each destination address is also checked for all
1’s, which is the reserved broadcast address.
The physical address registers are used to compare the destination address of incoming packets for rejecting or
accepting packets. Comparisons are performed on a byte wide basis. The bit assignment shown below relates the
sequence in PAR0-PAR5 to the bit sequence of the received packet.
Note:
The Multicast Address Registers provide filtering of multicast addresses hashed by the CRC logic. All destination
addresses are fed through the 32 bits CRC generation logic and as the last bit of the destination address enters the
CRC, the 6 most significant bits of the CRC generator are latched. These 6 bits are then decoded by a 1 of 64 decode
to index a unique filter bit (FB0-63) in the Multicast Address Registers. If the filter bit selected is set, the multicast
packet is accepted. The system designer would use a program to determine which filter bits to set in the multicast
registers. All multicast filter bits that correspond to Multicast Address Registers accepted by the node are then set to
one. To accept all multicast packets all of the registers are set to all ones.
The bit sequence of the received packet is DA0, DA1, … DA7, DA8 ….
DA15
DA23
DA31
DA39
DA47
FB15
FB23
FB31
FB39
FB47
FB55
FB63
DA7
FB7
D7
D7
DA14
DA22
DA30
DA38
DA46
FB14
FB22
FB30
FB38
FB46
FB54
FB62
DA6
FB6
D6
D6
DA13
DA21
DA29
DA37
DA45
FB13
FB21
FB29
FB37
FB45
FB53
FB61
DA5
FB5
D5
D5
DA12
DA20
DA28
DA36
DA44
FB12
FB20
FB28
FB36
FB44
FB52
FB60
DA4
FB4
D4
D4
12
DA11
DA19
DA27
DA35
DA43
FB11
FB19
FB27
FB35
FB43
FB51
FB59
DA3
FB3
D3
D3
AX88796BLF / AX88796BLI
ASIX ELECTRONICS CORPORATION
DA10
DA18
DA26
DA34
DA42
FB10
FB18
FB26
FB34
FB42
FB50
FB58
DA2
FB2
D2
D2
DA17
DA25
DA33
DA41
FB17
FB25
FB33
FB41
FB49
FB57
DA1
DA9
FB1
FB9
D1
D1
DA16
DA24
DA32
DA40
FB16
FB24
FB32
FB40
FB48
FB56
DA0
DA8
FB0
FB8
D0
D0