SX1231-31SKB868-EVAL Semtech, SX1231-31SKB868-EVAL Datasheet - Page 27
SX1231-31SKB868-EVAL
Manufacturer Part Number
SX1231-31SKB868-EVAL
Description
development tool usb kit for sx1231 transceiver...
Manufacturer
Semtech
Datasheet
1.SX1231-31SKB433.pdf
(84 pages)
- Current page: 27 of 84
- Download datasheet (2Mb)
3.5.7. DC Cancellation
DC cancellation is required in zero-IF architecture transceivers to remove any DC offset generated through self-reception.
It is built-in the SX1231 and its adjustable cutoff frequency fc is controlled in RegRxBw:
The default value of DccFreq cutoff frequency is typically 4% of the RxBw (channel filter BW). The cutoff frequency of the
DCC can however be increased to slightly improve the sensitivity, under wider modulation conditions. It is advised to adjust
the DCC setting while monitoring the receiver sensitivity.
3.5.8. Complex Filter - OOK
In OOK mode the SX1231 is modified to a low-IF architecture. The IF frequency is automatically set to half the single side
bandwidth of the channel filter (F
A complex filter is implemented on the chip to attenuate the resulting image frequency by typically 30 dB.
Note
3.5.9. RSSI
The RSSI block evaluates the amount of energy available within the receiver channel bandwidth. Its resolution is 0.5 dB,
and it has a wide dynamic range to accommodate both small and large signal levels that may be present. Its acquisition
time is very short, taking only 2 bit periods. The RSSI sampling must occur during the reception of preamble in FSK, and
constant “1” reception in OOK.
Note
Rev 4 - Nov 2010
ADVANCED COMMUNICATIONS & SENSING
this filter is automatically bypassed when receiving FSK signals (ModulationType = 00 in RegDataModul).
- The receiver is capable of automatic gain calibration, in order to improve the precision of its RSSI measurements.
This function injects a known RF signal at the LNA input, and calibrates the receiver gain accordingly. This
calibration is automatically performed during the PLL start-up, making it a transparent process to the end-user
- RssiValue can only be read when it exceeds RssiThreshold
01b / 20
00b / 16
10b / 24
01b / 20
00b / 16
10b / 24
01b / 20
00b / 16
10b / 24
01b / 20
00b / 16
10b / 24
01b / 20
00b / 16
IF
= 0.5 x RxBw). The Local Oscillator is automatically offset by the IF in the OOK receiver.
4
4
3
3
3
2
2
2
1
1
1
0
0
0
fc
=
----------------------------------------- -
2π
Page 27
×
4 RxBw
2
×
DccFreq
100.0
125.0
166.7
200.0
250.0
333.3
400.0
500.0
25.0
31.3
41.7
50.0
62.5
83.3
+
2
100.0
125.0
166.7
200.0
250.0
12.5
15.6
20.8
25.0
31.3
41.7
50.0
62.5
83.3
DATASHEET
www.semtech.com
SX1231
Related parts for SX1231-31SKB868-EVAL
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
EVALUATION BOARD
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
VOLTAGE SUPPRESSOR, TRANSIENT SEMTECH
Manufacturer:
Semtech
Datasheet:
Part Number:
Description:
HIGH VOLTAGE CAPACITORS MONOLITHIC CERAMIC TYPE
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
EZ1084CM5.0 AMP POSITIVE VOLTAGE REGULATOR
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
3.0 AMP LOW DROPOUT POSITIVE VOLTAGE REGULATORS
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
RailClamp Low Capacitance TVS Diode Array
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet:
Part Number:
Description:
Manufacturer:
Semtech Corporation
Datasheet: