GTL1655DGG,518 NXP Semiconductors, GTL1655DGG,518 Datasheet - Page 19

• Manufacturer Part Number: GTL1655DGG,518
• Description: IC TXRX BUS 16BIT 3-3.6V TSSOP64
• Manufacturer: NXP Semiconductors

Specifications of GTL1655DGG,518

• Logic Function: *
• Number Of Bits: 16
• Input Type: *
• Output Type: *
• Data Rate: *
• Number Of Channels: *
• Number Of Outputs/channel: *
• Differential - Input:output: *
• Propagation Delay (max): *
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TSSOP
• Mounting Type: Surface Mount
• Supply Voltage: 3 V ~ 3.6 V
• Logic Type: LVTTL-TO-GTL/GTL+ TRANSCEIVER
• Logic Family: GTL
• Operating Supply Voltage (typ): 3.3V
• Propagation Delay Time: 7.2ns
• Number Of Elements: 1
• Input Logic Level: LVTTL/TTL
• Output Logic Level: GTL
• Package Type: TSSOP
• Polarity: Non-Inverting
• Logical Function: Universal Bus Transceiver
• Operating Supply Voltage (min): 3V
• Technology: BiCMOS
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 64
• Operating Supply Voltage (max): 3.6V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 935270638518; GTL1655DGG-T; GTL1655DGG-T

Philips Semiconductors
13. Soldering
9397 750 12936
Product data
13.1 Introduction to soldering surface mount packages
13.2 Reflow soldering
13.3 Wave soldering
This text gives a very brief insight to a complex technology. A more in-depth account
of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit
Packages (document order number 9398 652 90011).
There is no soldering method that is ideal for all surface mount IC packages. Wave
soldering can still be used for certain surface mount ICs, but it is not suitable for fine
pitch SMDs. In these situations reflow soldering is recommended. In these situations
reflow soldering is recommended.
Reflow soldering requires solder paste (a suspension of fine solder particles, flux and
binding agent) to be applied to the printed-circuit board by screen printing, stencilling
or pressure-syringe dispensing before package placement. Driven by legislation and
environmental forces the worldwide use of lead-free solder pastes is increasing.
Several methods exist for reflowing; for example, convection or convection/infrared
heating in a conveyor type oven. Throughput times (preheating, soldering and
cooling) vary between 100 and 200 seconds depending on heating method.
Typical reflow peak temperatures range from 215 to 270 C depending on solder
paste material. The top-surface temperature of the packages should preferably be
kept:
Moisture sensitivity precautions, as indicated on packing, must be respected at all
times.
Conventional single wave soldering is not recommended for surface mount devices
(SMDs) or printed-circuit boards with a high component density, as solder bridging
and non-wetting can present major problems.
To overcome these problems the double-wave soldering method was specifically
developed.
If wave soldering is used the following conditions must be observed for optimal
results:
•
•
•
below 225 C (SnPb process) or below 245 C (Pb-free process)
below 240 C (SnPb process) or below 260 C (Pb-free process) for packages with
a thickness < 2.5 mm and a volume < 350 mm
Use a double-wave soldering method comprising a turbulent wave with high
upward pressure followed by a smooth laminar wave.
– for all BGA, HTSSON..T and SSOP..T packages
– for packages with a thickness
– for packages with a thickness < 2.5 mm and a volume
thick/large packages.
Rev. 01 — 11 May 2004
16-bit LVTTL-to-GTL/GTL+ bus transceiver with live insertion
2.5 mm
3
so called small/thin packages.
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
350 mm
GTL1655
3
so called
19 of 23