MAX1157BEUI+ Maxim Integrated, MAX1157BEUI+ Datasheet - Page 11
![no-image](/images/no-image-200.jpg)
MAX1157BEUI+
Manufacturer Part Number
MAX1157BEUI+
Description
Analog to Digital Converters - ADC 14-Bit 135ksps 4.2V Precision ADC
Manufacturer
Maxim Integrated
Datasheet
1.MAX1157AEUI.pdf
(15 pages)
Specifications of MAX1157BEUI+
Rohs
yes
Number Of Channels
1
Architecture
SAR
Conversion Rate
135 KSPs
Resolution
14 bit
Input Type
Single-Ended
Snr
85 dB
Interface Type
Parallel
Operating Supply Voltage
4.75 V to 5.25 V
Maximum Operating Temperature
+ 85 C
Package / Case
TSSOP-28
Maximum Power Dissipation
1026 mW
Minimum Operating Temperature
- 40 C
Number Of Converters
1
Voltage Reference
4.096 V
Figure 8. MAX1157 Transfer Function
Figure 10. MAX1175 Transfer Function
Figures 8, 9, and 10 show the MAX1157/MAX1159/
MAX1175’s output transfer functions. The MAX1159
and MAX1175 outputs are coded in offset binary, while
the MAX1157 is coded on standard binary.
Most applications require an input buffer amplifier to
achieve 14-bit accuracy and prevent loading the
source. Switch the channels immediately after acquisi-
tion, rather than near the end of or after a conversion
when the input signal is multiplexed. This allows more
time for the input buffer amplifier to respond to a large
11 . . . 1111
11 . . . 1110
10 . . . 0001
10 . . . 0000
00 . . . 0011
00 . . . 0010
11 . . . 1101
01 . . . 1111
00 . . . 0001
00 . . . 0000
11 . . . 111
11 . . . 110
11 . . . 101
00 . . . 011
00 . . . 010
00 . . . 001
00 . . . 000
OUTPUT CODE
OUTPUT CODE
-8192
0
-8191 -8189
14-Bit, 135ksps, Single-Supply ADCs with
1
-8190
______________________________________________________________________________________
2
3
INPUT VOLTAGE (LSB)
INPUT VOLTAGE (LSB)
INPUT RANGE = -5V TO +5V
-1
INPUT RANGE = 0 TO +10V
FULL-SCALE
TRANSITION
FULL-SCALE
TRANSITION
0
+1
Transfer Function
FULL-SCALE RANGE
(FSR) = +10V
FULL-SCALE RANGE
(FSR) = +10V
+8190
16382
1LSB =
1LSB =
+8191
16383
Input Buffer
+8192
16384
16384 x 4.096
16384 x 4.096
FSR x V
FSR x V
REF
REF
Bipolar Analog Input Range
step-change in input signal. The input amplifier must
have a high enough slew rate to complete the required
output voltage change before the beginning of the
acquisition time. Figure 11 shows an example of this
circuit using the MAX427.
Figures 12a and 12b show how the MAX1175 and
MAX1159 analog input current varies depending on
whether the chip is operating or powered down. The
part is fully powered down between conversions if the
voltage at R/C is set high during the second falling
edge of CS. The input current abruptly steps to the
powered up value at the start of acquisition. This step
in the input current can disrupt the ADC input, depend-
ing on the driving circuit’s output impedance at high
frequencies. If the driving circuit cannot fully settle by
the end of acquisition time, the accuracy of the system
can be compromised. To avoid this situation, increase
the acquisition time, use a driving circuit that can settle
within t
up by setting the voltage at R/C low during the second
falling edge of CS.
For best performance, use printed circuit (PC) boards.
Do not run analog and digital lines parallel to each
other, and do not lay out digital signal paths under-
neath the ADC package. Use separate analog and dig-
ital ground planes with only one point connecting the
two ground systems (analog and digital) as close to the
device as possible.
Route digital signals far away from sensitive analog and
reference inputs. If digital lines must cross analog lines,
do so at right angles to minimize coupling digital noise
Figure 9. MAX1159 Transfer Function
11 . . . 1111
11 . . . 1110
10 . . . 0001
10 . . . 0000
00 . . . 0011
00 . . . 0010
11 . . . 1101
01 . . . 1111
00 . . . 0001
00 . . . 0000
ACQ
OUTPUT CODE
, or leave the MAX1175/MAX1159 powered
Layout, Grounding, and Bypassing
-8192
-8191 -8189
-8190
INPUT VOLTAGE (LSB)
INPUT RANGE = -10V TO +10V
-1
FULL-SCALE
TRANSITION
0
+1
FULL-SCALE RANGE
(FSR) = +20V
+8190
1LSB =
+8191
+8192
16384 x 4.096
FSR x V
REF
11