MAX1064ACEG Maxim Integrated, MAX1064ACEG Datasheet
MAX1064ACEG
Specifications of MAX1064ACEG
Related parts for MAX1064ACEG
MAX1064ACEG Summary of contents
Page 1
... QSOP MAX1060BEEI -40°C to +85°C 28 QSOP Ordering Information continued at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. o 10-Bit Resolution, ±0.5 LSB Linearity o +5V Single-Supply Operation o User-Adjustable Logic Level (+2 ...
Page 2
ADCs with +2.5V Reference and Parallel Interface ABSOLUTE MAXIMUM RATINGS V to GND ..............................................................-0. GND.........................................................-0.3V to +6V LOGIC CH0–CH7, COM to GND ............................-0. REF, REFADJ to GND.................................-0. ...
Page 3
ADCs with +2.5V Reference and Parallel Interface ELECTRICAL CHARACTERISTICS (continued +5V ±10%, COM = GND, REFADJ = V DD LOGIC cycle unless otherwise noted. Typical values ...
Page 4
ADCs with +2.5V Reference and Parallel Interface ELECTRICAL CHARACTERISTICS (continued +5V ±10%, COM = GND, REFADJ = V DD LOGIC cycle unless otherwise noted. Typical values ...
Page 5
ADCs with +2.5V Reference and Parallel Interface TIMING CHARACTERISTICS (continued +5V ±10%, COM = GND, REFADJ = V DD LOGIC cycle unless otherwise noted. Typical values ...
Page 6
ADCs with +2.5V Reference and Parallel Interface ( +5V +2.500V LOGIC REF INTEGRAL NONLINEARITY vs. OUTPUT CODE 0.25 0.20 0.15 0.10 0.05 0 -0.05 -0.10 -0.15 -0.20 -0.25 0 ...
Page 7
ADCs with +2.5V Reference and Parallel Interface ( +5V +2.500V LOGIC REF INTERNAL REFERENCE VOLTAGE vs. SUPPLY VOLTAGE 2.53 2.52 2.51 2.50 2.49 2.48 4.50 4.75 5.00 5.25 V ...
Page 8
ADCs with +2.5V Reference and Parallel Interface PIN NAME MAX1060 MAX1064 High Byte Enable. Used to multiplex the 10-bit conversion result HBEN 1: 2 MSBs are multiplexed on the data bus LSBs ...
Page 9
ADCs with +2.5V Reference and Parallel Interface (CH7) (CH6) (CH5) (CH4) ANALOG INPUT CH3 MULTIPLEXER CH2 CH1 CH0 COM CLK CLOCK CS CONTROL LOGIC WR RD LATCHES INT ( ) ARE FOR MAX1060 ONLY. Figure 2. ...
Page 10
ADCs with +2.5V Reference and Parallel Interface 10-BIT CAPACITIVE DAC REF INPUT C HOLD MUX ZERO – + CH0 CH1 12pF R CH2 IN 800Ω CH3 C SWITCH HOLD CH4 TRACK CH5 AT THE SAMPLING INSTANT, ...
Page 11
ADCs with +2.5V Reference and Parallel Interface the acquisition interval. The ACQMOD (acquisition mode) bit in the input control byte (Table 1) offers two options for acquiring the signal: an internal and an external acquisition. The ...
Page 12
ADCs with +2.5V Reference and Parallel Interface CSWS CONTROL D7–D0 BYTE ACQMOD = 0 INT RD HBEN HIGH-Z DOUT Figure 4. Conversion Timing Using Internal Acquisition Mode ...
Page 13
ADCs with +2.5V Reference and Parallel Interface Select internal clock mode to release the µP from the burden of running the SAR conversion clock. To select this mode, bit D7 of the control byte must be ...
Page 14
ADCs with +2.5V Reference and Parallel Interface Digital Interface Input (control byte) and output data are multiplexed on a tri-state parallel interface. This parallel interface (I/O) can easily be interfaced with standard µPs. Signals CS, WR, ...
Page 15
ADCs with +2.5V Reference and Parallel Interface Table 5. Data-Bus Output ( Parallel Interface) PIN HBEN = 0 HBEN = 1 D0 Bit 0 (LSB) D1 Bit 1 Bit 9 (MSB) BIPOLAR (UNI/BIP = ...
Page 16
ADCs with +2.5V Reference and Parallel Interface only 50µs are required after power-up. Enter standby mode by performing a dummy conversion with the con- trol byte specifying standby mode. Note: Bypass capacitors larger than 4.7µF between ...
Page 17
ADCs with +2.5V Reference and Parallel Interface High-frequency noise in the power supply (V influence the proper operation of the ADC’s fast com- parator. Bypass V to the star ground with a network DD of two ...
Page 18
ADCs with +2.5V Reference and Parallel Interface SUPPLIES +3V V 4.7µ 5Ω 0.1µF GND V COM DD MAX1060 MAX1064 *OPTIONAL Figure 11. Power-Supply and Grounding Connections Signal-to-Noise Ratio For a waveform perfectly reconstructed from ...
Page 19
... CLK QSOP ______________________________________________________________________________________ +2.7V TO +5.5V +5V +2.5V µP CONTROL 4.7µF 0.1µF INPUTS OUTPUT STATUS ANALOG INPUTS GND µP DATA BUS Ordering Information (continued) PART 28 V LOGIC MAX1064ACEG MAX1064BCEG 26 REF MAX1064AEEG MAX1064BEEG 25 REFADJ 24 GND 23 COM 22 CH0 21 CH1 TRANSISTOR COUNT: 5781 20 CH2 19 CH3 18 CH4 ...
Page 20
... Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 20 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2003 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products ...