STM32F207ICH6 STMicroelectronics, STM32F207ICH6 Datasheet - Page 97

• Manufacturer Part Number: STM32F207ICH6
• Description: ARM Microcontrollers - MCU 32-Bit ARM Cortex M3 CAM 256 kB
• Manufacturer: STMicroelectronics

Specifications of STM32F207ICH6

• Product Category: ARM Microcontrollers - MCU
• Rohs: yes
• Core: ARM Cortex M3
• Data Bus Width: 32 bit

STM32F20xxx
All I/Os are CMOS and TTL compliant (no software configuration required). Their
characteristics cover more than the strict CMOS-technology or TTL parameters.
Output driving current
The GPIOs (general purpose input/outputs) can sink or source up to ±8 mA, and sink or
source up to ±20 mA (with a relaxed V
sink or source up to ±3mA. When using the PC13 to PC15 GPIOs in output mode, the
speed should not exceed 2 MHz with a maximum load of 30 pF.
In the user application, the number of I/O pins which can drive current must be limited to
respect the absolute maximum rating specified in
●
●
Output voltage levels
Unless otherwise specified, the parameters given in
performed under ambient temperature and V
Table
Table 45.
1. PC13, PC14, PC15 and PI8 are supplied through the power switch. Since the switch only sinks a limited
2. The I
3. The I
V
V
Symbol
V
V
V
V
V
V
OH
OH
OL
OL
OH
OL
OH
amount of current (3 mA), the use of GPIOs PC13 to PC15 and PI8 in output mode is limited: the speed
should not exceed 2 MHz with a maximum load of 30 pF and these I/Os must not be used as a current
source (e.g. to drive an LED).
and the sum of I
Table 10
OL
(2)(4)
(2)(4)
(3)(4)
(3)(4)
The sum of the currents sourced by all the I/Os on V
consumption of the MCU sourced on V
I
The sum of the currents sunk by all the I/Os on V
consumption of the MCU sunk on V
I
VDD
VSS
(2)
(3)
(2)
(3)
12. All I/Os are CMOS and TTL compliant.
IO
IO
current sunk by the device must always respect the absolute maximum rating specified in
current sourced by the device must always respect the absolute maximum rating specified in
(see
(see
Output low level voltage for an I/O pin
when 8 pins are sunk at same time
Output high level voltage for an I/O pin
when 8 pins are sourced at same time
Output low level voltage for an I/O pin
when 8 pins are sunk at same time
Output high level voltage for an I/O pin
when 8 pins are sourced at same time
Output low level voltage for an I/O pin
when 8 pins are sunk at same time
Output high level voltage for an I/O pin
when 8 pins are sourced at same time
Output low level voltage for an I/O pin
when 8 pins are sunk at same time
Output high level voltage for an I/O pin
when 8 pins are sourced at same time
and the sum of I
Output voltage characteristics
Table
Table
IO
(I/O ports and control pins) must not exceed I
10).
10).
Parameter
IO
(I/O ports and control pins) must not exceed I
Doc ID 15818 Rev 9
OL
SS
/V
OH
DD,
cannot exceed the absolute maximum rating
DD
(1)
) except PC13, PC14 and PC15 which can
cannot exceed the absolute maximum rating
supply voltage conditions summarized in
2.7 V < V
2.7 V < V
2.7 V < V
2 V < V
Section
I
CMOS ports
Conditions
I
IO
I
I
Table 45
IO
IO
TTL ports
IO
SS
= +20 mA
= +8 mA
= +6 mA
VSS
=+ 8mA
DD
DD
DD
DD
plus the maximum Run
DD,
.
5.2:
< 2.7 V
< 3.6 V
< 3.6 V
< 3.6 V
plus the maximum Run
are derived from tests
VDD
Electrical characteristics
.
V
V
V
DD
DD
DD
Min
2.4
-
-
-
-
–0.4
–1.3
–0.4
Max
0.4
0.4
1.3
0.4
Table 10
-
-
-
-
97/177
Unit
V
V
V
V