CAT25256ZD2I-GT2 ON Semiconductor, CAT25256ZD2I-GT2 Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/4/495/on_semiconductor_sml.jpg)
CAT25256ZD2I-GT2
Manufacturer Part Number
CAT25256ZD2I-GT2
Description
EEPROM 256KB SPI SER CMOS EEPROM
Manufacturer
ON Semiconductor
Datasheet
1.CAT25256ZD2I-GT2.pdf
(20 pages)
Specifications of CAT25256ZD2I-GT2
Rohs
yes
Memory Size
256 Kbit
Organization
32 x 8
Data Retention
100 yr
Maximum Clock Frequency
1000 KHz
Maximum Operating Current
2 mA
Operating Supply Voltage
1.8 V to 5.5 V
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Package / Case
TDFN-8
Interface Type
SPI
Minimum Operating Temperature
- 40 C
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
CAT25256ZD2I-GT2
Manufacturer:
ON/安森美
Quantity:
20 000
Read from Memory Array
followed by a 16−bit address (see Table 14 for the number
of significant address bits).
respond by shifting out data on the SO pin (as shown in
Figure 9). Sequentially stored data can be read out by simply
continuing to run the clock. The internal address pointer is
automatically incremented to the next higher address as data
is shifted out. After reaching the highest memory address,
the address counter “rolls over” to the lowest memory
address, and the read cycle can be continued indefinitely.
The read operation is terminated by taking CS high.
Read Identification Page
achieved using the same Read command sequence as used
for Read from main memory array (Figure 9). The IPL bit
from the Status Register must be set (IPL = 1) before
attempting to read from the IP. The [A5:A0] are the address
significant bits that point to the data byte shifted out on the
SO pin. If the CS continues to be held low, the internal
SCK
SCK
To read from memory, the host sends a READ instruction
After receiving the last address bit, the CAT25256 will
Reading the additional 64−byte Identification Page (IP) is
CS
CS
SO
SO
SI
SI
Dashed Line = mode (1, 1)
* Please check the Byte Address Table (Table 14)
Dashed Line = mode (1, 1)
0
0
0
0
0
1
0
0
2
1
0
3
HIGH IMPEDANCE
OPCODE
OPCODE
0
2
0
4
0
0
HIGH IMPEDANCE
5
3
1
6
0
4
1
7
A
N
8
1
5
Figure 10. RDSR Timing
Figure 9. READ Timing
READ OPERATIONS
http://onsemi.com
9
BYTE ADDRESS*
6
0
10
11
1
7
20
address register defined by [A5:A0] bits is automatically
incremented and the next data byte from the IP is shifted out.
The byte address must not exceed the 64−byte page
boundary.
Read Status Register
command. After receiving the last bit of the command, the
CAT25256 will shift out the contents of the status register on
the SO pin (Figure 10). The status register may be read at
any time, including during an internal write cycle. While the
internal write cycle is in progress, the RDSR command will
output the full content of the status register (New product,
Rev. E) or the RDY (Ready) bit only (i.e., data out = FFh) for
previous product revisions C, D (Mature product). For easy
detection of the internal write cycle completion, both during
writing to the memory array and to the status register, we
recommend sampling the RDY bit only through the polling
routine. After detecting the RDY bit “0”, the next RDSR
instruction will always output the expected content of the
status register.
MSB
To read the status register, the host simply sends a RDSR
21
8
7
22 23 24 25 26 27 28 29
9
6
A
0
10
MSB
5
7
11
6
4
DATA OUT
5
12
3
DATA OUT
4
3
13
2
2
14
30
1
1
0
0