1893BKLFT IDT, 1893BKLFT Datasheet - Page 18
1893BKLFT
Manufacturer Part Number
1893BKLFT
Description
Ethernet ICs 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER
Manufacturer
IDT
Datasheet
1.1893BKLF.pdf
(133 pages)
Specifications of 1893BKLFT
Rohs
yes
Part # Aliases
ICS1893BKLFT
- Current page: 18 of 133
- Download datasheet (807Kb)
4.1.2 Specific Reset Operations
4.1.2.1 Hardware Reset
4.1.2.2 Power-On Reset
ICS1893BF, Rev. F, 5/13/10
This section discusses the following specific ways that the ICS1893BF can be reset:
•
•
•
Note:
Entering Hardware Reset
Holding the active-low RESETn pin low for a minimum of five REF_IN clock cycles initiates a hardware
reset (that is, the ICS1893BF enters the reset state). During reset, the ICS1893BF executes the steps
listed in
Exiting Hardware Reset
After the signal on the RESETn pin transitions from a low to a high state, the ICS1893BF completes in 640
ns (that is, in 16 REF_IN clocks) steps 1 through 5, listed in
five steps are completed, the Serial Management Port is ready for normal operations, but this action does
not signify the end of the reset cycle. The reset cycle completes when the transmit clock (TXCLK) and
receive clock (RXCLK) are available, which is typically 53 ms after the RESETn pin goes high. [For details
on this transition, see
Note:
1. The MAC Interface is not available for use until the TXCLK and RXCLK are valid.
2. The Control Register bit 0.15 does not represent the status of a hardware reset. It is a self-clearing bit
Entering Power-On Reset
When power is applied to the ICS1893BF, it waits until the potential between VDD and VSS achieves a
minimum voltage before entering reset and executing the steps listed in
After entering reset from a power-on condition, the ICS1893BF remains in reset for approximately 20 µs.
(For details on this transition, see
Exiting Power-On Reset
The ICS1893BF automatically exits reset and performs the same steps as for a hardware reset. (See
Section 4.1.1.2, “Exiting
Note:
Hardware reset (using the RESETn pin)
Power-on reset (applying power to the ICS1893BF)
Software reset (using Control Register bit 0.15)
that is used to initiate a software reset.
ICS1893BF Data Sheet - Release
At the completion of a reset (either hardware, power-on, or software), the ICS1893BF sets all
registers to their default values.
The only difference between a hardware reset and a power-on reset is that during a power-on
reset, the ICS1893BF isolates its RESETn input pin. All other functionality is the same. As with a
hardware reset, Control Register bit 0.15 does not represent the status of a power-on reset.
Section 4.1.1.1, “Entering
Section 9.5.16, “Reset: Hardware Reset and
Reset”.)
Section 9.5.15, “Reset: Power-On
Reset”.
Copyright © 2009, IDT, Inc.
All rights reserved.
18
Section 4.1.1.2, “Exiting
Power-Down”.]
Reset”.)
Chapter 4 Operating Modes Overview
Section 4.1.1.1, “Entering
Reset”. After the first
May, 2010
Reset”.
Related parts for 1893BKLFT
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Ethernet ICs 3.3V 10/100 BASE TX INTEGRATED PHYCEIVER
Manufacturer:
IDT
Part Number:
Description:
PHYCEIVER LOW PWR 3.3V 56-MLF2
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet:
Part Number:
Description:
IDT TS3000AND TSE2002 SENSORS SAMPLE PACK OFFER
Manufacturer:
Integrated Device Technology (Idt)
Part Number:
Description:
THERMOCOUPLE DIGITAL PANEL METER
Manufacturer:
NEWPORT ELECTRONICS
Part Number:
Description:
High-performance CMOS bus interface latches
Manufacturer:
Integrated Device Technology, Inc.
Part Number:
Description:
Accessories Connectors and Cables
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
Accessories 5.25 Industrial Disk Tray
Manufacturer:
ADVANTECH [Advantech Co., Ltd.]
Datasheet:
Part Number:
Description:
IDT PART
Manufacturer:
IDT, Integrated Device Technology Inc
Datasheet: