AT24C01BN-SH-B Atmel, AT24C01BN-SH-B Datasheet - Page 22

• Manufacturer Part Number: AT24C01BN-SH-B
• Description: IC EEPROM 1KBIT 1MHZ 8SOIC
• Manufacturer: Atmel

Specifications of AT24C01BN-SH-B

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 1K (128 x 8)
• Speed: 400kHz, 1MHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Organization: 128 K x 8
• Interface Type: 2-Wire
• Maximum Clock Frequency: 1 MHz
• Access Time: 550 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1.8 V
• Maximum Operating Current: 3 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 1.8 V, 5.5 V
• Memory Configuration: 128 X 8
• Clock Frequency: 1MHz
• Supply Voltage Range: 1.8V To 5.5V
• Memory Case Style: SOIC
• No. Of Pins: 8
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12. 5TS1 – SOT23
22
NOTES: 1. This drawing is for general information only. Refer to JEDEC Drawing
AT24C01B
R
2. Dimension D does not include mold flash, protrusions, or gate burrs.
3. The package top may be smaller than the package bottom. Dimensions
4. These dimensions apply to the flat section of the lead between 0.08 mm
5. Dimension "b" does not include Dambar protrusion. Allowable Dambar
1150 E. Cheyenne Mtn. Blvd.
Colorado Springs, CO 80906
MO-193, Variation AB, for additional information.
Mold flash, protrusions, or gate burrs shall not exceed 0.15 mm per end.
Dimension E1 does not include interlead flash or protrusion. Interlead
flash or protrusion shall not exceed 0.15 mm per side.
D and E1 are determined at the outermost extremes of the plastic body
exclusive of mold flash, tie bar burrs, gate burrs, and interlead flash, but
including any mismatch between the top and bottom of the plastic body.
and 0.15 mm from the lead tip.
protrusion shall be 0.08 mm total in excess of the "b" dimension at
maximum material condition. The Dambar cannot be located on the lower
radius of the foot. Minimum space between protrusion and an adjacent lead
shall not be less than 0.07 mm.
Seating
Plane
E1
1
5
Top View
b
Side View
TITLE
5TS1, 5-lead, 1.60 mm Body, Plastic Thin Shrink
Small Outline Package (SHRINK SOT)
e1
D
2
e
3
4
A2
E
A1
A
SYMBOL
A
A1
A2
c
D
E
E1
L1
e
e1
b
0.30
COMMON DIMENSIONS
0.00
0.70
0.08
MIN
(Unit of Measure = mm)
–
C
End View
2.90 BSC
2.80 BSC
1.60 BSC
0.95 BSC
1.90 BSC
0.60 REF
NOM
0.90
–
–
–
–
DRAWING NO.
C
PO5TS1
L1
L
MAX
1.10
0.10
1.00
0.20
0.50
5156E–SEEPR–10/08
NOTE
4, 5
2, 3
2, 3
2, 3
4
6/25/03
REV.
A