DS2154LA2 Maxim Integrated, DS2154LA2 Datasheet - Page 30
DS2154LA2
Manufacturer Part Number
DS2154LA2
Description
Network Controller & Processor ICs
Manufacturer
Maxim Integrated
Datasheet
1.DS2154LA2.pdf
(87 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 30 of 87
- Download datasheet (2Mb)
DS2154
4.4 Power-Up Sequence
On power-up, after the supplies are stable, the DS2154 should be configured for operation by writing to
all of the internal registers (this includes the Test Registers) since the contents of the internal registers
cannot be predicted on power-up. Next, the LIRST (CCR5.7) bit should be toggled from 0 to 1 to reset
the line interface circuitry (it will take the DS2154 about 40ms to recover from the LIRST bit being
toggled). Finally, after the RSYSCLK and TSYSCLK inputs are stable, the ESR bit should be toggled
from a 0 to a 1 and then back to 0 (this step can be skipped if the elastic stores are not being used). Both
TCLK and RCLKI must be present for the parallel control port to operate properly.
4.5 Automatic Alarm Generation
When either CCR2.4 or CCR2.5 is set to 1, the DS2154 monitors the receive side to determine if any of
the following conditions are present: loss of receive frame synchronization, AIS alarm (all 1s) reception,
or loss of receive carrier (or signal). If any one (or more) of the above conditions is present, then the
DS2154 will either force an AIS alarm (if CCR2.5 = 1) or a Remote Alarm (CCR2.4 = 1) to be
transmitted via the TPOSO and TNEGO pins. It is an illegal state to have both CCR2.4 and CCR2.5 set to
1 at the same time. If CCR2.4 = 1, then RAI will be transmitted according to ETS 300 011 specifications
and a constant Remote Alarm will be transmitted if the DS2154 cannot find CRC4 multiframe
synchronization within 400ms as per G.706.
30 of 87
Related parts for DS2154LA2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Ds2154 Enhanced E1 Single Chip Transceiver
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products