DS21Q41BT+ Maxim Integrated, DS21Q41BT+ Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
DS21Q41BT+
Manufacturer Part Number
DS21Q41BT+
Description
Network Controller & Processor ICs
Manufacturer
Maxim Integrated
Datasheet
1.DS21Q41BT.pdf
(61 pages)
Specifications of DS21Q41BT+
Product
Framer
Number Of Transceivers
4
Data Rate
2.048 Mbps
Supply Current (max)
30 mA
Maximum Operating Temperature
+ 70 C
Mounting Style
SMD/SMT
Package / Case
TQFP-128
Minimum Operating Temperature
0 C
Operating Supply Voltage
5 V
Supply Voltage - Max
5.5 V
Supply Voltage - Min
4.5 V
Part # Aliases
90-21Q41+BT0
DS21Q41B
DS21Q41B PIN DESCRIPTION Table 1-4
Transmit Clock [TCLK]. 1.544 MHz primary clock. Used to clock data through the transmit side
formatter.
Transmit Serial Data [TSER]. Transmit NRZ serial data. Sampled on the falling edge of TCLK when
the transmit side elastic store is disabled. Sampled on the falling edge of TSYSCLK when the transmit
side elastic store is enabled.
Transmit Channel Clock [TCHCLK]. 192 kHz clock which pulses high during the LSB of each
channel. Synchronous with TCLK when the transmit side elastic store is disabled. Synchronous with
TSYSCLK when the transmit side elastic store is enabled. Useful for parallel to serial conversion of
channel data, locating robbed-bit signaling bits, and for blocking clocks in DDS applications. See Section
12 for timing details.
Transmit Bipolar Data [TPOS and TNEG]. Updated on rising edge of TCLK. Can be programmed to
output NRZ data on TPOS via the TCR1.7 control bit.
Transmit Channel Block [TCHBLK]. A user programmable output that can be forced high or low
during any of the 24 T1 channels. Synchronous with TCLK when the transmit side elastic store is
disabled. Synchronous with TSYSCLK when the transmit side elastic store is enabled. Useful for
blocking clocks to a serial UART or LAPD controller in applications where not all T1 channels are used
such as Fractional T1, 384k bps service, 768k bps, or ISDN-PRI. Also useful for locating individual
channels in drop-and-insert applications and for per-channel loopback. See Section 12 for timing details.
Transmit System Clock [TSYSCLK]. 1.544 MHz or 2.048 MHz clock. Only used when the transmit
side elastic store function is enabled. Should be tied low in applications that do not use the transmit side
elastic store.
Transmit Link Clock [TLCLK]. 4 kHz or 2 kHz (ZBTSI) demand clock for the TLINK input. See
Section 12 for timing details.
Transmit Link Data [TLINK]. If enabled via TCR1.2, this pin will be sampled during the F-bit time on
the falling edge of TCLK for data insertion into either the FDL stream (ESF) or the Fs bit position (D4)
or the Z-bit position (ZBTSI). See Section 12 for timing details.
Transmit Sync [TSYNC]. A pulse at this pin will establish either frame or multiframe boundaries for the
DS21Q41B. Via TCR2.2, the DS21Q41B can be programmed to output either a frame or multiframe
pulse at this pin. If this pin is set to output pulses at frame boundaries, it can also be set via TCR2.4 to
output double-wide pulses at signaling frames. See Section 12 for timing details.
Transmit Frame Sync [TFSYNC]. 8 kHz pulse. Only used when the transmit side elastic store is
enabled. A pulse at this pin will establish frame boundaries for the DS21Q41B. Should be tied low in
applications that do not use the transmit side elastic store. See Section 12 for timing details.
Receive Link Data [RLINK]. Updated with either FDL data (ESF) or Fs bits (D4) or Z bits (ZBTSI) one
RCLK before the start of a frame. See Section 12 for timing details.
Receive Link Clock [RLCLK]. 4 kHz or 2 kHz (ZBTSI) demand clock for the RLINK input. See
Section 12 for timing details.
8 of 61