MAX1808EUB+ Maxim Integrated, MAX1808EUB+ Datasheet - Page 18

• Manufacturer Part Number: MAX1808EUB+
• Description: Current & Power Monitors & Regulators
• Manufacturer: Maxim Integrated

The MAX15026 uses a bootstrap circuit to generate the
necessary gate-to-source voltage to turn on the high-
side MOSFET. The selected n-channel high-side
MOSFET determines the appropriate boost capaci-
tance value (C
according to the following equation:
where Q
MOSFET and ∆V
the high-side MOSFET driver after turn-on. Choose
∆V
cantly degraded (e.g. ∆V
determining C
the boost flying capacitor with a minimum value of
100nF.
The maximum power dissipation of the device depends
on the thermal resistance from the die to the ambient
environment and the ambient temperature. The thermal
resistance depends on the device package, PCB cop-
per area, other thermal mass, and airflow.
The power dissipated into the package (P
on the supply configuration (see the Typical Application
Circuits ). Use the following equation to calculate power
dissipation:
where I
lator, I
vers at DRV, and I
MAX15026 without the contribution of the I
in the Typical Operating Characteristics . For example, in
the application circuit of Figure 5, I
V
Use the following equation to estimate the temperature
rise of the die:
where θ
ance of the package, P
device, and T
24.4°C/W for 14-pin TDFN package on multilayer
boards, with the conditions specified by the respective
JEDEC standards (JESD51-5, JESD51-7). An accurate
Low-Cost, Small, 4.5V to 28V Wide Operating
Range, DC-DC Synchronous Buck Controller
MAX15026
18
DRV
BST
P
T
= V
= (V
DRV
so the available gate-drive voltage is not signifi-
LDO
JA
G
CC
IN
is the supply current consumed by the dri-
is the total gate charge of the high-side
is the junction-to-ambient thermal imped-
is the current supplied by the internal regu-
so that P
- V
BST
A
BST
CC
is the ambient temperature. The θ
BST
. Use a low-ESR ceramic capacitor as
T
) x I
J
in the Typical Application Circuits )
C
= T
is the voltage variation allowed on
T
IN
LDO
BST
= V
A
is the supply current of the
BST
T
+ (P
IN
=
+ V
is power dissipated in the
∆
x (I
= 100mV to 300mV) when
V
Q
DRV
T
BST
G
DRV
x θ
Power Dissipation
x I
LDO
Boost Capacitor
JA
+ I
DRV
)
IN
= I
).
+ V
DRV
DRV
T
) depends
CC
, as given
+ I
x I
IN
IN
JA
and
is
estimation of the junction temperature requires a direct
measurement of the case temperature (T
operating conditions significantly deviate from those
described in the JEDEC standards. The junction tem-
perature is then:
Use 8.7°C/W as θ
TDFN package. The case-to-ambient thermal imped-
ance (θ
ferred from the PCB to the ambient. Solder the exposed
pad of the TDFN package to a large copper area to
spread heat through the board surface, minimizing the
case-to-ambient thermal impedance. Use large copper
areas to keep the PCB temperature low.
Place all power components on the top side of the
board, and run the power stage currents using traces
or copper fills on the top side only. Make a star connec-
tion on the top side of traces to GND to minimize volt-
age drops in signal paths.
Keep the power traces and load connections short,
especially at the ground terminals. This practice is
essential for high efficiency and jitter-free operation. Use
thick copper PCBs (2oz or above) to enhance efficiency.
Place the MAX15026 adjacent to the synchronous recti-
fier MOSFET, preferably on the back side, to keep LX,
GND, DH, and DL traces short and wide. Use multiple
small vias to route these signals from the top to the bot-
tom side. Use an internal quiet copper plane to shield
the analog components on the bottom side from the
power components on the top side.
Make the MAX15026 ground connections as follows:
create a small analog ground plane near the device.
Connect this plane to GND and use this plane for the
ground connection for the V
pensation components, feedback dividers, V
tor, RT resistor, and LIM resistor.
Use Kelvin sense connections for LX and GND to the
synchronous rectifier MOSFET for current limiting to
guarantee the current-limit accuracy.
Route high-speed switching nodes (BST, LX, DH, and DL)
away from the sensitive analog areas (RT, COMP, LIM,
and FB). Group all GND-referred and feedback compo-
nents close to the device. Keep the FB and compensation
network as small as possible to prevent noise pickup.
CA
) is dependent on how well the heat is trans-
T
JC
J
= T
thermal impedance for the 14-pin
C
+ (P
PCB Layout Guidelines
IN
T
bypass capacitor, com-
x θ
JC
)
C
) when actual
Maxim Integrated
CC
capaci-