MAX24001TL+ Maxim Integrated, MAX24001TL+ Datasheet - Page 47

• Manufacturer Part Number: MAX24001TL+
• Description: Laser Drivers 2.5G Burst Mode Laser Xcvr
• Manufacturer: Maxim Integrated
• Type: Laser Driverr

Specifications of MAX24001TL+

• Rohs: yes
• Data Rate: 2.5 Gbps
• Operating Supply Voltage: 3 V to 3.6 V
• Supply Current: 136 mA
• Maximum Operating Temperature: + 95 C
• Package / Case: TQFN-40
• Maximum Power Dissipation: 2857.1 mW
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Part # Aliases: 90-Y24001+XS1

Maxim Integrated
BEh
BFh
C0h
C1h
E0h
7–1
7–6
4–0
BIT
BIT
BIT
BIT
BIT
7-4
7
6
5
4
3
2
1
0
3
2
1
0
0
5
7
6
5
4
3
2
1
0
pin_config0
—
dac_select
txsd_select
txfault_invert
los_invert
—
—
tx_disable_invert
pin_config1
—
apd_inhibit
txsd_allow
los_inhibit
laser_inhibit
software_faults
—
soft_tx_fault
temp_control
—
tempsense_pu
—
initialization_status
eeprom_unresponsive
eeprom_data_invalids
FIELD NAME
FIELD NAME
FIELD NAME
FIELD NAME
eeprom_dma_idle
tx_powerup_done
rx_powerup_done
FIELD NAME
—
—
—
TYPE
TYPE
TYPE
TYPE
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
—
—
—
—
—
TYPE
—
R
R
R
R
R
R
E
POR
POR
POR
POR
—
—
—
—
—
1
0
0
0
0
0
0
1
0
1
1
0
1
POR
—
0
0
1
0
0
0
0
Pin function and polarity configuration
Undefined
1: DAC pin 39, 0: TX_FAULT pin 39
1: TX_SD pin 21, 0: TX_FAULT pin 21
1: Invert the signal to TX_FAULT pin, 0: No inversion
1: LOS pin = 1 when signal detected and LOS pin = 0 when no signal
0: LOS pin = 1 when no signal detected and LOS = 0 when signal
Reserved
Reserved
1: Signal from TX_DISABLE pin is inverted, 0: No inversion
Masks outputs which should remain quiet during initialization
Undefined
1: APD_CTRL disabled (= Hi-Z), 0: Normal function
0: TX_SD disabled (= 1), 1: Normal function
1: LOS disabled (= 1), 0: Normal function
1: TX_OUT and BIAS are shutdown, 0: Normal function
This register is used to set fault conditions via the TWI
Undefined
1: Asserts the soft_tx_fault laser safety fault condition
Configures the temperature sensor
Undefined
0: temperature sensor powers down between reads
Undefined
Reports status associated with device initialisation.
Reserved
Undefined
1: EEPROM is idle and may be accessed
Reserved
1: Tx path power up during initialization is complete
1: Rx path power up during initialization is complete
1: Data integrity check failed during initialization
1: EEPROM failed to ACK the slave address during initialization
DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
DESCRIPTION
47