NCL30082ADMR2G ON Semiconductor, NCL30082ADMR2G Datasheet
NCL30082ADMR2G
Specifications of NCL30082ADMR2G
Available stocks
Related parts for NCL30082ADMR2G
NCL30082ADMR2G Summary of contents
Page 1
... V Under Voltage Lockout ♦ CC Thermal Shutdown ♦ This document contains information on a product under development. ON Semiconductor reserves the right to change or discontinue this product without notice. © Semiconductor Components Industries, LLC, 2013 March, 2013 − Rev. P3 http://onsemi.com Micro8 DM SUFFIX CASE 846A ...
Page 2
Figure 1. Typical Application Schematic for NCL30082 Table 1. PIN FUNCTION DESCRIPTION Pin No Pin Name Function 1 SD Thermal Fold−back and shutdown 2 ZCD Zero Crossing Detection 3 CS Current sense 4 GND − 5 DRV Driver output 6 ...
Page 3
Over Voltage Protection Over Temperature Protection SD Thermal V TF Foldback Qdrv Zero Crossing Detection ZCD Aux. Winding Short Circuit Prot. V offset_OK VIN Line Feedforward V CS Leading Constant−Current Edge Blanking Enable Max. Peak Current Limit CS Short Protection ...
Page 4
Table 2. MAXIMUM RATINGS TABLE Symbol V Maximum Power Supply voltage, VCC pin, continuous voltage CC(MAX) I Maximum current for VCC pin CC(MAX) V Maximum driver pin voltage, DRV pin, continuous voltage DRV(MAX) I Maximum current for DRV pin DRV(MAX) ...
Page 5
Table 3. ELECTRICAL CHARACTERISTICS For min/max values T = −40°C to +125°C, Max T J Description STARTUP AND SUPPLY CIRCUITS Supply Voltage Startup Threshold Minimum Operating Voltage Hysteresis V – V CC(on) CC(off) Internal logic reset Over Voltage Protection VCC ...
Page 6
Table 3. ELECTRICAL CHARACTERISTICS For min/max values T = −40°C to +125°C, Max T J Description ZERO VOLTAGE DETECTION CIRCUIT ZCD threshold voltage ZCD threshold voltage (Note 4) ZCD hysteresis (Note 4) Threshold voltage for output short circuit or aux. ...
Page 7
Table 3. ELECTRICAL CHARACTERISTICS For min/max values T = −40°C to +125°C, Max T J Description DIMMING SECTION DIM pin voltage for zero output current (OFF voltage) DIM pin voltage for maximum output current Dimming range Clamping voltage for DIM ...
Page 8
T , JUNCTION TEMPERATURE (°C) J Figure 3. V vs. Junction Temperature CC(on) 27.80 27.75 27.70 27.65 27.60 27.55 27.50 −40 − ...
Page 9
T , JUNCTION TEMPERATURE (°C) J Figure 9. I vs. Junction Temperature CC2 1.000 0.995 0.990 0.985 0.980 −40 − JUNCTION ...
Page 10
T , JUNCTION TEMPERATURE (°C) J Figure 15. t vs. Junction Temperature BLANK 255 254 253 252 251 250 249 −40 − JUNCTION ...
Page 11
T , JUNCTION TEMPERATURE (°C) J Figure 21. V vs. Junction Temperature REF(on) 2.300 2.295 2.290 2.285 2.280 2.275 2.270 −40 −20 0 ...
Page 12
T , JUNCTION TEMPERATURE (°C) J Figure 27. V vs. Junction VLY2−4/3−5 Temperature 76.0 75.5 75.0 74.5 74.0 73.5 73.0 −40 − ...
Page 13
T , JUNCTION TEMPERATURE (°C) J Figure 33. V VLY11−13/12−15 Temperature 0.710 0.705 0.700 0.695 0.690 −40 − JUNCTION ...
Page 14
T , JUNCTION TEMPERATURE (°C) J Figure 39. V vs. Junction Temperature OVP 0.690 0.688 0.686 0.684 0.682 0.680 −40 − ...
Page 15
Figure 45. t The NCL30082 implements a current−mode architecture operating in quasi−resonant mode. Thanks to proprietary circuitry, the controller is able to accurately regulate the secondary side current of the flyback ...
Page 16
Constant Current Control Figure 47 portrays the primary and secondary current of a flyback converter in discontinuous conduction mode (DCM). Figure 46 shows the basic circuit of a flyback converter. V bulk R C clp Clamping network DRV Figure 46. ...
Page 17
I (t) pri t Figure 47. Flyback Currents and Auxiliary Winding Voltage in DCM Internal Soft−Start At startup or after recovering from a fault, there is a small internal soft−start of 40 ms. In addition, during startup, as the output ...
Page 18
Figure 48. Startup Simulation Showing the Natural Soft−start Cycle−by−Cycle Current Limit When the current sense voltage exceeds the internal threshold V , the ...
Page 19
CS LEB1 + Rsense − Vcontrol + − V ILIMIT LEB2 + − V CS(stop) Figure 49. Winding Short Circuit Protection, Max. Peak Current Limit Circuits Thermal Fold−back and Over Voltage / Over Temperature Protection The thermal fold−back circuit reduces ...
Page 20
At startup, when V reaches V CC CC(on) not allowed to start pulsing for at least 180 ms in order to allow the SD pin voltage to reach its nominal value OVP VCC Vdd Dz I OTP(REF) ...
Page 21
CC(on) V CC(off) V CC(reset) V DRV V > OVP V controller stops SD switching V OVP V SD(clamp) V out Figure 52. OVP with SD Pin Chronograms 4−s Timer 4−s timer has elapsed: ...
Page 22
CC(on) V CC(off) V CC(reset) V DRV V < OTP(off) V controller stops SD switching V TF(start) V TF(stop) V OTP(off) I out Figure 53. Thermal Fold−back / OTP Chronograms PWM or Linear Dimming Detection ...
Page 23
V Over Voltage Protection (Open LED Protection output load is connected to the LED power supply, the controller must be able to safely limit the output voltage excursion. 40.0 V CC(OVP) 30.0 V CC(on) 20.0 10.0 V ...
Page 24
Vbulk VIN + − 2 LLine low 2 LLine high Table 4. VALLEY SELECTION I value at which the out controller changes valley (I decreasing) out 0 100% 75% 50% 30% 15 25−ms ...
Page 25
Zero Crossing Detection Block The ZCD pin allows detecting when the drain−source voltage of the power MOSFET reaches a valley. A valley is detected when the voltage on pin 1 crosses below the V internal threshold. ZCD(THD) At startup or ...
Page 26
ZCD V . ZCD(TH) V ZCD(short) Line Feed−Forward Because of the propagation delays, the MOSFET is not turned−off immediately when the current set−point is reached result, the primary peak current is higher than expected and the output current ...
Page 27
Brown−out In order to protect the supply against a very low input voltage, the NCL30082 features a brown−out circuit with a fixed ON/OFF threshold. The controller is allowed to start if a voltage higher than applied to ...
Page 28
CS Pin Short Circuit Protection Normally, if the CS pin or the sense resistor is shorted to ground, the Driver will not be able to turn off, leading to potential damage of the power supply. To avoid this, the NCL30082A ...
Page 29
Timer has finished counting OVP2 4−s Timer OVP2 or WOD_SCP or Aux_SCP or V _OVP CC With states: Reset → Controller is reset, I Stop → Controller is ON, DRV is not switching, t Run → Normal ...
Page 30
Timer has finished counting V < CC(reset) OVP2 or V 4−s CC Timer OVP2 or V _OVP CC Latch OTP or WOD_SCP or Aux_SCP With states: Reset → Controller is reset, I Stop → Controller is ON, DRV ...
Page 31
... PLANE A 0.038 (0.0015 *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. PACKAGE DIMENSIONS Micro8t CASE 846A−02 ISSUE H NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. ...
Page 32
... Auto−recovery NCL30082B1 Auto−recovery ORDERING INFORMATION Device Package Marking NCL30082ADMR2G NCL30082BDMR2G NCL30082B1DMR2G †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’ ...