NCL30082ADMR2G ON Semiconductor, NCL30082ADMR2G Datasheet - Page 15

• Manufacturer Part Number: NCL30082ADMR2G
• Description: LED Lighting Drivers Dimmable Quasi-Res I-Mode Cntlr
• Manufacturer: ON Semiconductor

Specifications of NCL30082ADMR2G

• Rohs: yes
• Input Voltage: 18 V
• Operating Frequency: 65 kHz
• Maximum Supply Current: 1.2 mA
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Package / Case: Micro-8
• Minimum Operating Temperature: - 40 C

operating in quasi−resonant mode. Thanks to proprietary
circuitry, the controller is able to accurately regulate the
secondary side current of the flyback converter without
using any opto−coupler or measuring directly the secondary
side current.
•
•
•
•
•
The NCL30082 implements a current−mode architecture
Quasi−Resonance Current−Mode Operation:
implementing quasi−resonance operation in peak
current−mode control, the NCL30082 optimizes the
efficiency by switching in the valley of the MOSFET
drain−source voltage. Thanks to a smart control
algorithm, the controller locks−out in a selected valley
and remains locked until the input voltage or the output
current set point significantly changes.
Primary Side Constant Current Control: thanks to a
proprietary circuit, the controller is able to compensate
for the leakage inductance of the transformer and allow
accurate control of the secondary side current.
Line Feed−forward: compensation for possible
variation of the output current caused by system slew
rate variation.
Open LED protection: if the voltage on the VCC pin
exceeds an internal limit, the controller shuts down and
waits 4 seconds before restarting switching.
Thermal Fold−back / Over Temperature / Over
Voltage Protection: by combining a dual threshold on
the SD pin, the controller allows the direct connection
of an NTC to ground plus a Zener diode to a monitored
voltage. The temperature is monitored and the output
current is linearly reduced in the event that the
56.0
55.5
55.0
54.5
54.0
53.5
53.0
52.5
−40
Figure 45. t
−20
TYPICAL CHARACTERISTICS
APPLICATION INFORMATION
T
J
, JUNCTION TEMPERATURE (°C)
0
BO(BLANK)
http://onsemi.com
20
vs. Junction Temperature
40
15
•
•
•
•
•
60
temperature exceeds a prescribed level. If the
temperature continues to increase, the current will be
further reduced until the controller is stopped. The
control will automatically restart if the temperature is
reduced. This pin can implement a programmable OVP
shutdown that can also auto−restart the device.
Brown−Out: the controller includes a brown−out
circuit which safely stops the controller in case the
input voltage is too low. The device will automatically
restart if the line recovers.
Cycle−by−cycle peak current limit: when the current
sense voltage exceeds the internal threshold V
MOSFET is turned off for the rest of the switching
cycle.
Winding Short−Circuit Protection: an additional
comparator with a short LEB filter (t
signal and stops the controller if V
V
enabled only during the main LEB duration t
Output Short−circuit protection: If a very low
voltage is applied on ZCD pin for 90 ms (nominal), the
controllers assume that the output or the ZCD pin is
shorted to ground and enters shutdown. The
auto−restart version (B suffix) waits 4 seconds, then the
controller restarts switching. In the latched version (A
suffix), the controller is latched as long as V
above the V
Linear or PWM dimming: the DIM pin allows
implementing both analog and PWM dimming.
ILIM
80
. For noise immunity reasons, this comparator is
100
CC(reset)
120
threshold.
CS
BCS
reaches 1.5 x
) senses the CS
CC
LEB
ILIM
stays
.
, the