VND5E008AY-E STMicroelectronics, VND5E008AY-E Datasheet

no-image

VND5E008AY-E

Manufacturer Part Number
VND5E008AY-E
Description
Power Switch ICs - Power Distribution Double Ch High Side 41V 8mOhm 76A 2uA
Manufacturer
STMicroelectronics
Datasheet

Specifications of VND5E008AY-E

Product Category
Power Switch ICs - Power Distribution
Rohs
yes
Features
1. Typical value with all loads connected
July 2012
This is information on a product in full production.
Max transient supply voltage
Operating voltage range
Typ on-state resistance (per ch.)
Current limitation (typ)
Off-state supply current
General:
– Inrush current active management by
– Very low standby current
– 3.0V CMOS compatible input
– Optimized electromagnetic emission
– Very low electromagnetic susceptibility
– Compliant with European directive
– Proportional load current sense
– High current sense precision for wide range
– Very low current sense leakage
Diagnostic functions:
– Off-state open-load detection
– Current sense disable
– Thermal shutdown indication
– Output short to V
– Overload and short to ground (power
Protection:
– Undervoltage shutdown
– Overvoltage clamp
– Load current limitation
– Self limiting of fast thermal transients
– Protection against loss of ground and loss
– Thermal shut down
– Reverse battery protection with self switch
power limitation
2002/95/EC
current
limitation) indication
of V
of the Power MOS
CC
Double channel high-side driver with analog current sense
CC
detection
I
V
V
R
LIMH
I
CC
CC
ON
S
4.5 to 28V
2 μA
8 mΩ
41 V
76 A
Doc ID 13620 Rev 3
(1)
Applications
Description
The VND5E008AY-E is a device made using
STMicroelectronics
It is intended for driving resistive or inductive
loads with one side connected to ground. Active
V
low energy spikes.
This device integrates an analog current sense
which delivers a current proportional to the load
current when CS_DIS high leads the current
sense pin in high impedance.
Fault conditions such as overload,
overtemperature or open-load are reported via
the current sense pin
Output current limitation protects the device in
overload condition. In case of long overload
duration, the device limits the dissipated power to
safe level up to thermal shutdown intervention.
Thermal shutdown with automatic restart allows
the device to recover normal operation as soon as
fault condition disappears.
CC
– Electrostatic discharge protection
All types of resistive, inductive and capacitive
loads
pin voltage clamp protects the device against
for automotive applications
PowerSSO-36
VND5E008AY-E
®
VIPower
Datasheet
®
MO-5 technology.
production data
www.st.com
1/39
1

Related parts for VND5E008AY-E

VND5E008AY-E Summary of contents

Page 1

... Electrostatic discharge protection Applications ■ All types of resistive, inductive and capacitive loads Description The VND5E008AY device made using STMicroelectronics It is intended for driving resistive or inductive loads with one side connected to ground. Active V pin voltage clamp protects the device against CC low energy spikes ...

Page 2

... Current sense and diagnostic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 3.3.1 3.4 Maximum demagnetization energy (V 4 Package and PCB thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 4.1 PowerSSO-36 thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 5 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 5.1 ECOPACK 5.2 PowerSSO-36 mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 5.3 Packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36 6 Order codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37 7 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 2/39 Short to VCC and off-state open-load detection . . . . . . . . . . . . . . . . . . 27 ® packages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33 Doc ID 13620 Rev 3 VND5E008AY ...

Page 3

... VND5E008AY-E List of tables Table 1. Pin function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Table 2. Suggested connections for unused and not connected pins . . . . . . . . . . . . . . . . . . . . . . . . 6 Table 3. Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Table 4. Thermal data Table 5. Power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Table 6. Switching (V = 13V Table 7. Current sense (8 V < V Table 8. Open-load detection (8 V < V Table 9. Protections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Table 10 ...

Page 4

... PowerSSO-36 Thermal impedance junction ambient single pulse (one channel ON Figure 38. Thermal fitting model of a double channel HSD in PowerSSO- Figure 39. PowerSSO-36 package dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34 Figure 40. PowerSSO-36 tube shipment (no suffix Figure 41. PowerSSO-36 tape and reel shipment (suffix “TR” 4/ case . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 CC Doc ID 13620 Rev 3 VND5E008AY-E ...

Page 5

... VND5E008AY-E 1 Block diagram and pin description Figure 1. Block diagram Table 1. Pin function Name V CC OUT 1,2 GND IN 1,2 CS 1,2 CS_DIS Battery connection Power output Ground connection Voltage controlled input pin with hysteresis, CMOS compatible. Controls output switch state Analog current sense pin, delivers a current proportional to the load current ...

Page 6

... Configuration diagram (top view) Table 2. Suggested connections for unused and not connected pins Connection / pin Floating To ground 6/39 Current sense N.C. Output Not allowed X Through 1 KΩ X resistor allowed Doc ID 13620 Rev 3 VND5E008AY-E Input X X Not Through 10 KΩ Through 10 KΩ resistor CS_DIS X resistor ...

Page 7

... VND5E008AY-E 2 Electrical specifications Figure 3. Current and voltage conventions 2.1 Absolute maximum ratings Table 3. Absolute maximum ratings Symbol V DC supply voltage CC V Transient supply voltage (T < 400 ms, R CCPK -V Reverse DC supply voltage CC Maximum supply voltage for full protection to short-circuit V CC_LSC (acc. AEC-Q100-012 reverse ground pin current ...

Page 8

... Thermal data Table 4. Thermal data Symbol Thermal resistance junction-case (MAX) (with one R thj-case channel ON) R Thermal resistance junction-ambient (MAX) thj-amb 8/39 Parameter Parameter Doc ID 13620 Rev 3 VND5E008AY-E Value Unit 750 V -40 to 150 °C -55 to 150 °C Max. value Unit 0.85 °C/W See Figure 36 in the ° ...

Page 9

... VND5E008AY-E 2.3 Electrical characteristics 8 V < V < -40 °C < Table 5. Power section Symbol Parameter V Operating supply voltage CC V Undervoltage shutdown USD Undervoltage shutdown V USDhyst hysteresis R ON-state resistance ON Reverse battery ON-state R ON REV resistance V Clamp Voltage clamp I Supply current S I Off-state output current L(off) 1 ...

Page 10

... A; V OUT ( (2) V < 1.5 A < I SENSE SENSE (see Figure Doc ID 13620 Rev 3 VND5E008AY-E Min. Typ. Max. Unit = 0.5 V SENSE 3658 6000 8926 = 0.5 V SENSE 3910 6000 4336 6000 = 0.5 V SENSE - SENSE 4948 6000 5298 6000 = 4 V ...

Page 11

... VND5E008AY-E Table 7. Current sense (8 V < V Symbol Delay Response time t from rising edge of DSENSE1L CS_DIS pin Delay Response time t from rising edge of DSENSE2H INPUT pin Delay response time between rising edge of Δt DSENSE2H output current and rising edge of current sense Delay Response time ...

Page 12

... Figure 10) Parameter Test conditions 0.9 V CSD = 2.1 V CSD CSD CSD Doc ID 13620 Rev 3 VND5E008AY-E Min. Typ. Max. Unit 7 °C V -29 V - Min. Typ. Max. Unit 0 µA 2 µA ...

Page 13

... VND5E008AY-E Figure 5. Open-load off-state delay timing Figure 6. I OUT Iou t/I /Isen se 10 10750 10000 10 9250 8500 7750 7000 6250 5500 4750 4000 3250 2500 0 Max - Max Typical - SENSE OUT 5.0 10.0 Iout [A] Iou 40 ° 150 50 °C 25 ° ...

Page 14

... Open-load off-state (with external pull up) 14/ Iout [A] Input (no power limitation Doc ID 13620 Rev 3 VND5E008AY Min - 150 C Output Sense (V CSD Nominal SENSEH Nominal Cycling V ...

Page 15

... VND5E008AY-E Table 11. Truth table Conditions Short circuit pull up disconnected) Negative output voltage clamp 1. If the V is high, the SENSE output high impedance, its potential depends on leakage currents CSD and external circuit. Figure 8. Switching characteristics Input L (external H L Doc ID 13620 Rev 3 ...

Page 16

... Electrical specifications Figure 9. Delay response time between rising edge of output current and rising edge of current sense (CS enabled) Figure 10. Output voltage drop limitation 16/39 Doc ID 13620 Rev 3 VND5E008AY-E ...

Page 17

... VND5E008AY-E Table 12. Electrical transient requirements (part 1) ISO 7637-2: 2004(E) Test pulse ( The above test levels must be considered referred Valid in case of external load dump clamp: 40V maximum referred to ground. Table 13. Electrical transient requirements (part 2) ISO 7637-2: 2004(E) ...

Page 18

... Electrical specifications 2.4 Waveforms Figure 11. Normal operation Figure 12. Overload or short to GND 18/39 Doc ID 13620 Rev 3 VND5E008AY-E ...

Page 19

... VND5E008AY-E Figure 13. Intermittent overload Doc ID 13620 Rev 3 Electrical specifications 19/39 ...

Page 20

... Electrical specifications Figure 14. Off-state open-load with external circuitry 20/39 Doc ID 13620 Rev 3 VND5E008AY-E ...

Page 21

... VND5E008AY-E Figure 15. Short to V Figure 16. T evolution in overload or short to GND J CC Doc ID 13620 Rev 3 Electrical specifications 21/39 ...

Page 22

... Electrical specifications 2.5 Electrical characteristics curves Figure 17. Off-state output current Figure 19. Input clamp voltage Figure 21. Input low level 22/39 Figure 18. High level input current Figure 20. Input high level Figure 22. Input hysteresis voltage Doc ID 13620 Rev 3 VND5E008AY-E ...

Page 23

... VND5E008AY-E Figure 23. On-state resistance vs T Figure 25. Undervoltage shutdown Figure 27. Turn-on voltage slope Figure 24. On-state resistance vs V case Figure 26. I LIMH Figure 28. Turn-off voltage slope Doc ID 13620 Rev 3 Electrical specifications case 23/39 ...

Page 24

... Electrical specifications Figure 29. CS_DIS clamp voltage Figure 31. High level CS_DIS voltage 24/39 Figure 30. Low level CS_DIS voltage Doc ID 13620 Rev 3 VND5E008AY-E ...

Page 25

... VND5E008AY-E 3 Application information Figure 32. Application schematic Note: Channel 2 has the same internal circuit as channel 1. 3.1 Load dump protection D is necessary (Voltage Transient Suppressor) if the load dump peak voltage exceeds the ld V max rating. The same applies if the device is subject to transients on the V CCPK that are greater than the ones shown in the ISO T/R 7637/1 table ...

Page 26

... SENSE in Table 7: Current sense (8 V < V SENSE Table 7: Current sense (8 V < case of the following fault conditions (refer to SENSEH table): in off-state CC Doc ID 13620 Rev 3 VND5E008AY-E Figure 33: Current sense and . X by means of an SENSE and V is ensured OUT SENSE < < ...

Page 27

... VND5E008AY-E Figure 33. Current sense and diagnostic 3.3.1 Short Short short-circuit between V V during the device off-state. Small or no current is delivered by the current sense SENSEH during the ON-state depending on the nature of the short-circuit. Off-state open-load with external circuitry Detection of an open-load in off mode requires an external pull-up resistor R ...

Page 28

... Pull up _ OFF ( ( ) ⋅ − ⋅ − Pull and I OLmin OLmax L(off2)r L(off2)f Doc ID 13620 Rev 3 VND5E008AY-E < off ) min ) ⋅ off ) 2 r > max PD (see Table 8: Open-load detection ...

Page 29

... VND5E008AY-E 3.4 Maximum demagnetization energy (V Figure 34. Maximum turn-off current versus inductance 150 °C (single pulse) jstart 100 °C (repetitive pulse) jstart 125 °C (repetitive pulse) jstart Note: Values are generated with R In case of repetitive pulses, T must not exceed the temperature specified above for curves A and B. ...

Page 30

... Note: Layout condition of R Board dimension 129 mm; Board Material FR4; Cu thickness 0.070 mm; Thermal vias separation 1.2 mm; Thermal via diameter 0.3 mm +/-0.08 mm; Cu thickness on vias 0.025 mm; Footprint dimension 4 6.5 mm) 30/39 and Z measurements (Board finish thickness 1.6 mm +/-10 %; Board double layer Doc ID 13620 Rev 3 VND5E008AY-E ...

Page 31

... VND5E008AY-E Figure 36. R thj-amb ON) Figure 37. PowerSSO-36 Thermal impedance junction ambient single pulse (one channel ON) vs PCB copper area in open box free air condition (one channel Doc ID 13620 Rev 3 Package and PCB thermal data 31/39 ...

Page 32

... T ⁄ = where Table 15. Thermal parameter Area/island ( (°C/ (°C/ (W.s/° (W.s/°C) 32/39 Z THtp 1 δ – (°C/W) R4 (°C/W) R5 (°C/W) R6 (°C/W) C3 (W.s/°C) C4 (W.s/°C) C5 (W.s/°C) C6 (W.s/°C) Doc ID 13620 Rev 3 VND5E008AY-E Footprint 2 0.05 0 0.004 0.008 0.04 0 ...

Page 33

... VND5E008AY-E 5 Package information ® 5.1 ECOPACK n order to meet environmental requirements, ST offers these devices in different grades of ® ECOPACK packages, depending on their level of environmental compliance. ECOPACK specifications, grade definitions and product status are available at: www.st.com. ® ECOPACK trademark. packages Doc ID 13620 Rev 3 Package information ® ...

Page 34

... Package information 5.2 PowerSSO-36 mechanical data Figure 39. PowerSSO-36 package dimensions 34/39 Doc ID 13620 Rev 3 VND5E008AY-E ...

Page 35

... VND5E008AY-E Table 16. PowerSSO-36 mechanical data Symbol Millimeters Min. Typ. 2.15 — 2.15 — 0 — 0.18 — 0.23 — 10.10 — 7.4 — — 0.5 — 8.5 — — — — 10.1 — — — 0.55 — — — 4.1 — 6.5 — Doc ID 13620 Rev 3 Package information Max ...

Page 36

... C (± 0.1) All dimensions are in mm 1.55 1.5 11.5 2.85 2 End Top No components cover 500mm min tape Empty components pockets saled with cover tape. User direction of feed Doc ID 13620 Rev 3 VND5E008AY-E 49 1225 532 3.5 13.8 0.6 REEL DIMENSIONS Base Q.ty 1000 1000 Bulk Q.ty 330 A (max) 1.5 B (min) C (± -0) 24 ...

Page 37

... VND5E008AY-E 6 Order codes Table 17. Device summary Package PowerSSO-36 Order codes Tube VND5E008AY-E Doc ID 13620 Rev 3 Order codes Tape and reel VND5E008AYTR-E 37/39 ...

Page 38

... Table 13: Electrical transient requirements (part 2) Added Section 2.4: Updated Section 2.5: Electrical characteristics curves Updated Chapter 3: Application information Updated Chapter 4: Package and PCB thermal data 3 Updated Figure 39: PowerSSO-36 package dimensions Doc ID 13620 Rev 3 VND5E008AY-E Changes vs I OUT enabled). = 13V 25° < ...

Page 39

... VND5E008AY-E Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. ...

Related keywords