7008L20JI IDT, 7008L20JI Datasheet - Page 17

• Manufacturer Part Number: 7008L20JI
• Description: SRAM
• Manufacturer: IDT
• Type: Dual Port Static RAMr

Specifications of 7008L20JI

• Memory Size: 512 kbit
• Organization: 64 k x 8
• Access Time: 20 ns
• Supply Voltage - Max: 5.5 V
• Supply Voltage - Min: 4.5 V
• Maximum Operating Current: 50 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Package / Case: PLCC-84
• Interface: TTL
• Memory Type: Asynchronous
• Part # Aliases: IDT7008L20JI

Busy Logic
have accessed the same location at the same time. It also allows one of the
two accesses to proceed and signals the other side that the RAM is “busy”.
The BUSY pin can then be used to stall the access until the operation on
the other side is completed. If a write operation has been attempted from
the side that receives a BUSY indication, the write signal is gated internally
to prevent the write from proceeding.
In some cases it may be useful to logically OR the BUSY outputs together
and use any BUSY indication as an interrupt source to flag the event of
an illegal or illogical operation. If the write inhibit function of BUSY logic is
not desirable, the BUSY logic can be disabled by placing the part in slave
mode with the M/S pin. Once in slave mode the BUSY pin operates solely
as a write inhibit input pin. Normal operation can be programmed by tying
the BUSY pins HIGH. If desired, unintended write operations can be
prevented to a port by tying the BUSY pin for that port LOW.
pull type outputs and do not require pull up resistors to operate. If these
RAMs are being expanded in depth, then the BUSY indication for the
resulting array requires the use of an external AND gate.
A
Width Expansion Busy Logic
Master/Slave Arrays
logic, one master part is used to decide which side of the RAMs array will
receive a BUSY indication, and to output that indication. Any number of
slaves to be addressed in the same address range as the master, use
the BUSY signal as a write inhibit signal. Thus on the IDT7008 RAM the
BUSY pin is an output if the part is used as a master (M/S pin = V
the BUSY pin is an input if the part used as a slave (M/S pin = V
in Figure 3.
decision could result with one master indicating BUSY on one side of the
array and another master indicating BUSY on one other side of the array.
This would inhibit the write operations from one port for part of a word and
inhibit the write operations from the other port for the other part of the word.
address signals only. It ignores whether an access is a read or write. In
a master/slave array, both address and chip enable must be valid long
enough for a BUSY flag to be output from the master before the actual write
pulse can be initiated with the R/W signal. Failure to observe this timing can
16
IDT7008S/L
High-Speed 64K x 8 Dual-Port Static RAM
Busy Logic provides a hardware indication that both ports of the RAM
The use of BUSY logic is not required or desirable for all applications.
The BUSY outputs on the IDT7008 RAM in master mode, are push-
When expanding an IDT7008 RAM array in width while using BUSY
If two or more master parts were used when expanding in width, a split
The BUSY arbitration, on a master, is based on the chip enable and
Figure 3. Busy and chip enable routing for both width and depth
BUSY (L)
BUSY (L)
MASTER
Dual Port RAM
MASTER
Dual Port RAM
expansion with IDT7008 RAMs.
BUSY (R)
BUSY (R)
CE
CE
0
1
BUSY (L)
SLAVE
Dual Port RAM
SLAVE
Dual Port RAM
BUSY (L)
BUSY (R)
BUSY (R)
CE
CE
0
1
IL
3198 drw 19
) as shown
IH
), and
,
6.42
17
result in a glitched internal write inhibit signal and corrupted data in the
slave.
Semaphores
with an additional 8 address locations dedicated to binary semaphore flags.
These flags allow either processor on the left or right side of the Dual-Port
RAM to claim a privilege over the other processor for functions defined by
the system designer’s software. As an example, the semaphore can be
used by one processor to inhibit the other from accessing a portion of the
Dual-Port RAM or any other shared resource.
completely independent of each other. This means that the activity on the
left port in no way slows the access time of the right port. Both ports are
identical in function to standard CMOS Static RAM and can be read from,
or written to, at the same time with the only possible conflict arising from the
simultaneous writing of, or a simultaneous READ/WRITE of, a non-
semaphore location. Semaphores are protected against such ambiguous
situations and may be used by the system program to avoid any conflicts
in the non-semaphore portion of the Dual-Port RAM. These devices have
an automatic power-down feature controlled by CE, the Dual-Port RAM
enable, and SEM, the semaphore enable. The CE and SEM pins control
on-chip power down circuitry that permits the respective port to go into
standby mode when not selected. This is the condition which is shown in
Truth Table II where CE and SEM are both HIGH.
or controllers and are typically very high-speed systems which are
software controlled or software intensive. These systems can benefit from
a performance increase offered by the IDT7008s hardware semaphores,
which provide a lockout mechanism without requiring complex program-
ming.
system flexibility by permitting shared resources to be allocated in varying
configurations. The IDT7008 does not use its semaphore flags to control
any resources through hardware, thus allowing the system designer total
flexibility in system architecture.
methods of hardware arbitration is that wait states are never incurred in
either processor. This can prove to be a major advantage in very high-
speed systems.
How the Semaphore Flags Work
of the Dual-Port RAM. These latches can be used to pass a flag, or token,
from one port to the other to indicate that a shared resource is in use. The
semaphores provide a hardware assist for a use assignment method
called “Token Passing Allocation.” In this method, the state of a semaphore
latch is used as a token indicating that shared resource is in use. If the left
processor wants to use this resource, it requests the token by setting the
latch. This processor then verifies its success in setting the latch by reading
it. If it was successful, it proceeds to assume control over the shared
resource. If it was not successful in setting the latch, it determines that the
right side processor has set the latch first, has the token and is using the
shared resource. The left processor can then either repeatedly request
that semaphore’s status or remove its request for that semaphore to perform
another task and occasionally attempt again to gain control of the token via
The IDT7008 is an extremely fast Dual-Port 64K x 8 CMOS Static RAM
The Dual-Port RAM features a fast access time, and both ports are
Systems which can best use the IDT7008 contain multiple processors
Software handshaking between processors offers the maximum in
An advantage of using semaphores rather than the more common
The semaphore logic is a set of eight latches which are independent
Military, Industrial and Commercial Temperature Ranges