M95010-WMN6TP STMicroelectronics, M95010-WMN6TP Datasheet - Page 10
![IC EEPROM 1KBIT 10MHZ 8SOIC](/photos/1/38/13851/497-8-soic_sml.jpg)
M95010-WMN6TP
Manufacturer Part Number
M95010-WMN6TP
Description
IC EEPROM 1KBIT 10MHZ 8SOIC
Manufacturer
STMicroelectronics
Datasheet
1.M95010-WMN6TP.pdf
(43 pages)
Specifications of M95010-WMN6TP
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
1K (128 x 8)
Speed
10MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Density
1Kb
Interface Type
Serial (SPI)
Organization
128x8
Access Time (max)
35ns
Frequency (max)
10MHz
Write Protection
Yes
Data Retention
40Year
Operating Supply Voltage (typ)
3.3/5V
Package Type
SOIC
Operating Temp Range
-40C to 85C
Supply Current
2mA
Operating Supply Voltage (min)
2.5V
Operating Supply Voltage (max)
5.5V
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
8
Maximum Clock Frequency
5 MHz
Supply Voltage (max)
5.5 V
Supply Voltage (min)
2.5 V
Maximum Operating Current
2 mA
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
3.3 V, 5 V
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-8672-2
M95010-WMN6TP
M95010-WMN6TP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M95010-WMN6TP
Manufacturer:
TI
Quantity:
21 000
Part Number:
M95010-WMN6TP
Manufacturer:
ST
Quantity:
20 000
Signal description
2.9.3
2.9.4
10/43
Power-up conditions
When the power supply is turned on, V
time, the Chip Select (S) line is not allowed to float but should follow the V
therefore recommended to connect the S line to V
Figure
In addition, the Chip Select (S) input offers a built-in safety feature, as the S input is edge
sensitive as well as level sensitive: after power-up, the device does not become selected
until a falling edge has first been detected on Chip Select (S). This ensures that Chip Select
(S) must have been high, prior to going low to start the first operation.
The V
defined in
Power-down
During power-down (continuous decrease in the V
V
●
●
CC
operating voltage defined in
deselected (Chip Select S should be allowed to follow the voltage applied on V
in Standby Power mode (there should not be any internal write cycle in progress).
CC
3).
voltage has to rise continuously from 0 V up to the minimum V
Table
8,
Table 9
and
Doc ID 6512 Rev 8
Table 10
Table
CC
8,
and the rise time must not vary faster than 1 V/µs.
Table 9
rises continuously from V
and
CC
CC
via a suitable pull-up resistor (see
supply voltage below the minimum
Table
10), the device must be:
M95040, M95020, M95010
SS
to V
CC
CC
operating voltage
CC
voltage. It is
. During this
CC
)