25LC512-I/SM Microchip Technology, 25LC512-I/SM Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
25LC512-I/SM
Manufacturer Part Number
25LC512-I/SM
Description
IC EEPROM 512KBIT 20MHZ 8SOIC
Manufacturer
Microchip Technology
Datasheet
1.25LC512-ISM.pdf
(36 pages)
Specifications of 25LC512-I/SM
Memory Size
512K (64K x 8)
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Speed
20MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
Memory Configuration
64K X 8
Ic Interface Type
SPI
Clock Frequency
20MHz
Supply Voltage Range
2.5V To 5.5V
Memory Case Style
SOIJ
No. Of Pins
9
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
25LC512-I/SM
Manufacturer:
MICROCHIP
Quantity:
12 000
Part Number:
25LC512-I/SM
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
25LC512
2.12
Once the device has entered Deep Power-Down
mode all instructions are ignored except the Release
from Deep Power-down and Read Electronic Signa-
ture command. This command can also be used when
the device is not in Deep power-down to read the
electronic signature out on the SO pin unless another
command is being executed such as Erase, Program
or Write Status Register.
FIGURE 2-12:
Driving CS high after the 8-bit RDID command but before the Electronic Signature has been transmitted will still ensure
the device will be taken out of Deep Power-Down mode. However, there is a delay T
returns to Standby mode (I
FIGURE 2-13:
DS22065C-page 18
SCK
SO
CS
SI
RELEASE FROM DEEP
POWER-DOWN AND READ
ELECTRONIC SIGNATURE
1
0
SCK
SO
CS
SI
0
1
1
Instruction
RELEASE FROM DEEP POWER-DOWN AND READ ELECTRONIC SIGNATURE
2
RELEASE FROM DEEP POWER-DOWN AND READ ELECTRONIC SIGNATURE
1
0
0
3
CCS
0
1
1
), as shown in Figure 2-13.
4
1
Instruction
2
0
5
0
High-Impedance
3
1
6
1
4
1
7
0
5
15 14 13 12
8
High-Impedance
1
6
9 10 11
1
7
16-bit Address
Release from Deep Power-Down mode and Read
Electronic Signature is entered by driving CS low,
followed by the RDID instruction code (Figure 2-12)
and then a dummy address of 16 bits (A15-A0). After
the last bit of the dummy address is clock in, the 8-bit
Electronic Signature is clocked out on the SO pin.
After the signature has been read out at least once,
the sequence can be terminated by driving CS high.
The device will then return to Standby mode and will
wait to be selected so it can be given new instructions.
If additional clock cycles are sent after the electronic
signature has been read once, it will continue to output
the signature on the SO line until the sequence is
terminated.
21 22 23 24 25 26 27 28 29 30 31
2
1
0
T
REL
7
0
Electronic Signature Out
REL
Manufacturer’s ID = 0x29
6
0
2010 Microchip Technology Inc.
that occurs before the device
5
1
4
0
3
1
2
0
1
0
0
1