SST89E554RC-40-I-TQJE Microchip Technology, SST89E554RC-40-I-TQJE Datasheet - Page 57

• Manufacturer Part Number: SST89E554RC-40-I-TQJE
• Description: 8-bit Microcontrollers - MCU 32KB+8KB 40ns
• Manufacturer: Microchip Technology

Specifications of SST89E554RC-40-I-TQJE

• Rohs: yes
• Core: 8051
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 40 MHz
• Program Memory Size: 32 KB
• Data Ram Size: 1 KB
• On-chip Adc: No
• Operating Supply Voltage: 4.5 V to 5.5 V
• Package / Case: TQFP-44
• Mounting Style: SMD/SMT
• Data Rom Size: 128 B
• Interface Type: SPI, UART
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Number Of Programmable I/os: 32
• Number Of Timers: 16 bit
• Processor Series: FlashFlex
• Program Memory Type: Flash
• Supply Voltage - Max: 5.5 V
• Supply Voltage - Min: 4.5 V

FlashFlex MCU
SST89E564RD / SST89V564RD
SST89E554RC / SST89V554RC
8.3.4 Pulse Width Modulator
The Pulse Width Modulator (PWM) mode is used to gener-
ate 8-bit PWMs by comparing the low byte of the PCA
timer (CL) with the low byte of the compare register
(CCAPnL). When CL < CCAPnL the output is low. When
CL ≥ CCAPnL the output is high. To activate this mode, the
user must set the PWM and ECOM bits in the module’s
CCAPMn SFR. (See Figure 8-5 and Table 8-7)
In PWM mode, the frequency of the output depends on the
source for the PCA timer. Since there is only one set of CH
and CL registers, all modules share the PCA timer and fre-
quency. Duty cycle of the output is controlled by the value
TABLE
©2007 Silicon Storage Technology, Inc.
PCA Timer Mode
1/12 Oscillator Frequency
1/4 Oscillator Frequency
Timer 0 Overflow:
External Input (Max)
FIGURE
8-bit
16-bit
8-bit Auto-Reload
8-7: P
8-5: PCA P
ULSE
ECOMn CAPPn CAPNn MATn
Enable
W
IDTH
Overflow
ULSE
M
0
ODULATOR
W
IDTH
PCA Timer/Counter
0
8-bit Comparator
M
ODULATOR
CCAPnH
CCAPnL
F
REQUENCIES
CL
0
3.9 KHz to 15.3 Hz
TOGn
M
0
ODE
11.8 KHz
12 MHz
3.9 KHz
15.5 Hz
0.06 Hz
5.9 KHz
57
PWMn ECCFn
loaded into the high byte (CCAPnH). Since writes to the
CCAPnH register are asynchronous, a new value written to
the high byte will not be shifted into CCAPnL for compari-
son until the next period of the output (when CL rolls over
from 255 to 00).
To calculate values for CCAPnH for any duty cycle, use
the following equation:
where CCAPnH is an 8-bit integer and Duty Cycle is a
fraction.
CL < CCAPnL
CL >= CCAPnL
0
PWM Frequency
CCAPnH = 256(1 - Duty Cycle)
CCAPMn
n=0 to 4
0
1
5.2 KHz to 20.3 Hz
15.6 KHz
5.2 KHz
7.8 KHz
1207 F38.2
16 MHz
20.3 Hz
0.08 Hz
S71207-08-EOL
CEXn
EOL Data Sheet
T8-7.0 1207
1/07