SST89E554RC-40-C-NJ Microchip Technology, SST89E554RC-40-C-NJ Datasheet - Page 33
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
SST89E554RC-40-C-NJ
Manufacturer Part Number
SST89E554RC-40-C-NJ
Description
8-bit Microcontrollers - MCU 32KB+8KB 40ns
Manufacturer
Microchip Technology
Datasheet
1.SST89E564RD-40-I-NJE.pdf
(90 pages)
Specifications of SST89E554RC-40-C-NJ
Core
8051
Data Bus Width
8 bit
Maximum Clock Frequency
40 MHz
Program Memory Size
32 KB
Data Ram Size
1 KB
On-chip Adc
No
Operating Supply Voltage
4.5 V to 5.5 V
Package / Case
PLCC-44
Mounting Style
SMD/SMT
Data Rom Size
128 B
Interface Type
SPI, UART
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Number Of Programmable I/os
32
Number Of Timers
16 bit
On-chip Dac
No
Processor Series
FlashFlex
Program Memory Type
Flash
Supply Voltage - Max
5.5 V
Supply Voltage - Min
4.5 V
FlashFlex MCU
SST89E564RD / SST89V564RD
SST89E554RC / SST89V554RC
Timer/Counter 2 Control Register (T2CON)
Timer/Counter 2 Mode Control (T2MOD)
©2007 Silicon Storage Technology, Inc.
Location
Location
C8H
C9H
Symbol
TF2
EXF2
RCLK
TCLK
EXEN2
TR2
C/T2#
CP/RL2#
Symbol
-
T2OE
DCEN
TF2
7
7
-
EXF2
6
Function
Timer 2 overflow flag set by a Timer 2 overflow and must be cleared by software. TF2
will not be set when either RCLK or TCLK = 1.
Timer 2 external flag set when either a capture or reload is caused by a negative
transition on T2EX and EXEN2 = 1. When Timer 2 interrupt is enabled, EXF2 = 1 will
cause the CPU to vector to the Timer 2 interrupt routine. EXF2 must be cleared by
software. EXF2 does not cause an interrupt in up/down counter mode (DCEN = 1).
Receive clock flag. When set, causes the serial port to use Timer 2 overflow pulses for
its receive clock in modes 1 and 3. RCLK = 0 causes Timer 1 overflow to be used for
the receive clock.
Transmit clock flag. When set, causes the serial port to use Timer 2 overflow pulses for
its transmit clock in modes 1 and 3. TCLK = 0 causes Timer 1 overflow to be used for
the transmit clock.
Timer 2 external enable flag. When set, allows a capture or reload to occur as a result
of a negative transition on T2EX if Timer 2 is not being used to clock the serial port.
EXEN2 = 0 causes Timer 2 to ignore events at T2EX.
Start/stop control for Timer 2. A logic 1 starts the timer.
Timer or counter select (Timer 2)
0: Internal timer (OSC/6 in 6 clock mode, OSC/12 in 12 clock mode)
1: External event counter (falling edge triggered)
Capture/Reload flag. When set, captures will occur on negative transitions at T2EX if
EXEN2 = 1. When cleared, auto-reloads will occur either with Timer 2 overflows or
negative transitions at T2EX when EXEN2 = 1. When either RCLK = 1 or TCLK = 1,
this bit is ignored and the timer is forced to auto-reload on Timer 2 overflow.
6
Function
Not implemented, reserved for future use.
Note: User should not write ‘1’s to reserved bits. The value read from a reserved bit is indeterminate.
Timer 2 Output Enable bit.
Down Count Enable bit. When set, this allows Timer 2 to be configured as an up/down
counter.
-
RCLK
5
5
-
TCLK
4
4
-
33
EXEN2
3
3
-
TR2
2
2
-
C/T2#
T2OE
1
1
CP/RL2#
DCEN
0
0
S71207-08-EOL
EOL Data Sheet
Reset Value
Reset Value
xxxxxx00b
00H
1/07