SST89E554RC-40-C-TQJ Microchip Technology, SST89E554RC-40-C-TQJ Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
SST89E554RC-40-C-TQJ
Manufacturer Part Number
SST89E554RC-40-C-TQJ
Description
8-bit Microcontrollers - MCU 32KB+8KB 40ns
Manufacturer
Microchip Technology
Datasheet
1.SST89E564RD-40-I-NJE.pdf
(90 pages)
Specifications of SST89E554RC-40-C-TQJ
Core
8051
Data Bus Width
8 bit
Maximum Clock Frequency
40 MHz
Program Memory Size
32 KB
Data Ram Size
1 KB
On-chip Adc
No
Operating Supply Voltage
4.5 V to 5.5 V
Package / Case
TQFP-44
Mounting Style
SMD/SMT
Data Rom Size
128 B
Interface Type
SPI, UART
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Number Of Programmable I/os
32
Number Of Timers
16 bit
On-chip Dac
No
Processor Series
FlashFlex
Program Memory Type
Flash
Supply Voltage - Max
5.5 V
Supply Voltage - Min
4.5 V
FlashFlex MCU
SST89E564RD / SST89V564RD
SST89E554RC / SST89V554RC
2.1 Pin Descriptions
TABLE
©2007 Silicon Storage Technology, Inc.
Symbol
P0[7:0]
P1[7:0]
P2[7:0]
P3[7:0]
P1[0]
P1[1]
P1[2]
P1[3]
P1[4]
P1[5]
P1[6]
P1[7]
P3[0]
P3[1]
2-1: P
I/O with internal
with internal
with internal
IN
pull-up
pull-up
pull-up
Type
D
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
O
I
I
I
ESCRIPTIONS
1
Name and Functions
Port 0: Port 0 is an 8-bit open drain bi-directional I/O port. As an output port each pin can
sink several LS TTL inputs. Port 0 pins that have ‘1’s written to them float, and in this state
can be used as high-impedance inputs. Port 0 is also the multiplexed low-order address and
data bus during accesses to external code and data memory. In this application, it uses
strong internal pull-ups when transitioning to ‘1’s. Port 0 also receives the code bytes during
the external host mode programming, and outputs the code bytes during the external host
mode verification. External pull-ups are required during program verification or as a general
purpose I/O port.
Port 1: Port 1 is an 8-bit bi-directional I/O port with internal pull-ups. The Port 1 output buffers
can drive LS TTL inputs. Port 1 pins are pulled high by the internal pull-ups when ‘1’s are writ-
ten to them and can be used as inputs in this state. As inputs, Port 1 pins that are externally
pulled low will source current (I
P1[5, 6, 7] have high current drive of 16 mA. Port 1 also receives the low-order address bytes
during the external host mode programming and verification.
T2: External count input to Timer/Counter 2 or Clock-out from Timer/Counter 2
T2EX: Timer/Counter 2 capture/reload trigger and direction control
ECI: External Clock Input
This signal is the external clock input for the PCA.
CEX0: Capture/Compare External I/O for PCA Module 0
Each capture/compare module connects to a Port 1 pin for external I/O.
When not used by the PCA, this pin can handle standard I/O.
SS#: Slave port select input for SPI
OR
CEX1: Capture/Compare External I/O for PCA Module 1
MOSI: Master Output line, Slave Input line for SPI
OR
CEX2: Capture/Compare External I/O for PCA Module 2
MISO: Master Input line, Slave Output line for SPI
OR
CEX3: Capture/Compare External I/O for PCA Module 3
SCK: Master clock output, slave clock input line for SPI
OR
CEX4: Capture/Compare External I/O for PCA Module 4
Port 2: Port 2 is an 8-bit bi-directional I/O port with internal pull-ups. Port 2 pins are pulled
high by the internal pull-ups when ‘1’s are written to them and can be used as inputs in this
state. As inputs, Port 2 pins that are externally pulled low will source current (I
13-6 and 13-7) because of the internal pull-ups. Port 2 sends the high-order address byte
during fetches from external program memory and during accesses to external Data Memory
that use 16-bit address (MOVX@DPTR). In this application, it uses strong internal pull-ups
when transitioning to ‘1’s. Port 2 also receives some control signals and a partial of high-order
address bits during the external host mode programming and verification.
Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. The Port 3 output buffers
can drive LS TTL inputs. Port 3 pins are pulled high by the internal pull-ups when ‘1’s are writ-
ten to them and can be used as inputs in this state. As inputs, Port 3 pins that are externally
pulled low will source current (I
Port 3 also receives some control signals and a partial of high-order address bits during the
external host mode programming and verification.
RXD: Universal Asynchronous Receiver/Transmitter (UART) - Receive input
TXD: UART - Transmit output
(1
OF
2)
11
IL
IL
, see Tables 13-6 and 13-7) because of the internal pull-ups.
, see Tables 13-6 and 13-7) because of the internal pull-ups.
S71207-08-EOL
EOL Data Sheet
IL
, see Tables
1/07