AT24C08B-TH-T Atmel, AT24C08B-TH-T Datasheet
AT24C08B-TH-T
Specifications of AT24C08B-TH-T
Available stocks
Related parts for AT24C08B-TH-T
AT24C08B-TH-T Summary of contents
Page 1
... GND SDA 5 4 Bottom View Bottom View 8-lead TSSOP 8-lead SOIC SCL GND SDA GND 5-lead SOT23 8-lead PDIP SCL GND SDA GND 4 CC Two-wire Serial EEPROM 4K (512 (1024 x 8) AT24C04B AT24C08B GND SCL SDA SCL SDA 5226G–SEEPR–11/09 ...
Page 2
Absolute Maximum Ratings Operating Temperature .......................... • 55°C to +125°C Storage Temperature ........................... • 65° 150°C Voltage on Any Pin with Respect to Ground ................................... • 0.1V to +7.0V Maximum Operating Voltage .................................... 6.25V DC Output Current.................................................. 5.0 ...
Page 3
... The A0 pin connect and can be connected to ground (device addressing is discussed in detail under the Device Addressing section). The AT24C08B only uses the A2 input for hardware addressing and a total of two 8K devices may be addressed on a single bus system. The A0 and A1 pins are no connects and can be connected to ground (device addressing is discussed in detail under the Device Addressing section) ...
Page 4
... Memory Organization AT24C04B, 4K SERIAL EEPROM: word address for random word addressing. AT24C08B, 8K SERIAL EEPROM: data word address for random word addressing. Table 2. Pin Capacitance Applicable over recommended operating range from T Symbol C Input/Output Capacitance (SDA) I/O C Input Capacitance (A IN Note: 1. This parameter is characterized and is not 100% tested. ...
Page 5
Table 4. AC Characteristics Applicable over recommended operating range from TTL Gate and 100 pF (unless otherwise noted) Symbol f Clock Frequency, SCL SCL t Clock Pulse Width Low LOW t Clock Pulse Width High HIGH ...
Page 6
Device Operation CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (see start or stop condition as defined below. START ...
Page 7
Bus Timing Figure 4. SCL: Serial Clock, SDA: Serial Data I/O SCL t SU.STA SDA IN SDA OUT 5. Write Cycle Timing Figure 5. SCL: Serial Clock, SDA: Serial Data I/O SCL SDA 8th BIT WORDn Note: 1. The ...
Page 8
Figure 6. Data Validity SDA SCL Figure 7. Start and Stop Definition SDA SCL Figure 8. Output Acknowledge SCL DATA IN DATA OUT AT24C04B/08B 8 DATA STABLE DATA STABLE DATA ...
Page 9
... The device address word consists of a mandatory one, zero sequence for the first four most significant bits as shown. This is common to all the EEPROM devices. The 4K EEPROM only uses the A2 and A1 device address bits with the third bit being a memory page address bit. The two device address bits must compare to their corresponding hard-wired input pins. The A0 pin is no connect. ...
Page 10
... This address stays valid between operations as long as the chip power is maintained. The address “roll over” during read is from the last byte of the last memory page to the first byte of the first page. The address “roll over” during write is from the last byte of the current page to the first byte of the same page ...
Page 11
Figure 10. Byte Write Figure 11. Page Write Figure 12. Current Address Read 5226G–SEEPR–11/09 Two-wire Serial EEPROM 11 ...
Page 12
Figure 13. Random Read Figure 14. Sequential Read AT24C04B/08B 12 5226G–SEEPR–11/09 ...
Page 13
AT24C04B Ordering Information Table 5. Ordering Information Ordering Code AT24C04B-PU (Bulk form only) (1) AT24C04BN-SH-B (NiPdAu Lead Finish) (2) AT24C04BN-SH-T (NiPdAu Lead Finish) (1) AT24C04B-TH-B (NiPdAu Lead Finish) (2) AT24C04B-TH-T (NiPdAu Lead Finish) (2) AT24C04BY6-YH-T (NiPdAu Lead Finish) (2) ...
Page 14
... AT24C08B Ordering Information Table 6. Ordering Information Ordering Code AT24C08B-PU (Bulk form only) (1) AT24C08BN-SH-B (NiPdAu Lead Finish) (2) AT24C08BN-SH-T (NiPdAu Lead Finish) (1) AT24C08B-TH-B (NiPdAu Lead Finish) (2) AT24C08B-TH-T (NiPdAu Lead Finish) (2) AT24C08BY6-YH-T (NiPdAu Lead Finish) (2) AT24C08B-TSU-T (2) AT24C08BU3-UU-T (3) AT24C08B-W-11 Note: 1. “-B” denotes bulk. 2. “-T” denotes tape and reel. SOIC = 4K per reel. TSSOP, Ultra Thin Mini-MAP, SOT23, and dBGA2 = 5K per reel ...
Page 15
Part Marketing Scheme 11.1. AT24C04B Device Package Marking 8-PDIP Seal Year Top Mark --- --- --- --- --- --- --- --- --- --- --- --- --- --- --- Lot Number --- ...
Page 16
... Pin 1 Indicator (Dot BUILD YEAR 2006 = 6 2007 = ATMEL LOT NUMBER TO COORESPOND WITH NSEB TRACE CODE LOG BOOK. (e. AA, AB, AC,...AX, AY, AZ) AT24C04B/08B YEAR OF ASSEMBLY ATMEL LOT NUMBER TO COORESPOND WITH NSEB TRACE CODE LOG BOOK. (e. AA, AB, AC,...AX, AY, AZ SEAL YEAR 6: 2006 7: 2007 8: 2008 9: 2009 ...
Page 17
SOT23 Top Mark Line 1 -----------> Device V = Voltage Indicator W = Write Protect Feature U = Material Set Bottom Mark --- --- --- --- --- --- --- --- Y = One Digit ...
Page 18
... AT24C08B Device Package Marking dBGA2 Line 1 -----------> Line 2 -----------> ONE DIGIT YEAR CODE 8: 2008 2009 2: 0: 2010 SEAL MONTH (USE ALPHA DESIGNATOR A- JANUARY B = FEBRUARY " " """"""" OCTOBER K = NOVEMBER L = DECEMBER XX = TRACE CODE (ATMEL LOT NUMBERS TO CORRESPOND ...
Page 19
... M = SEAL MONTH (USE ALPHA DESIGNATOR A- JANUARY B = FEBRUARY " " """"""" OCTOBER K = NOVEMBER L = DECEMBER XX = TRACE CODE (ATMEL LOT NUMBERS TO CORRESPOND WITH TRACE CODE LOG BOOK) 5226G–SEEPR–11/09 Seal Year Seal Week SEAL WEEK 2012 ...
Page 20
Pin 1 Indicator (Dot) --- --- --- --- * --- --- --- --- --- --- --- --- --- --- Bottom Mark --- --- --- --- --- --- --- --- --- ...
Page 21
Packaging Information 8P3 – PDIP Figure 15. 8P3 – PDIP Top View PLCS Side View Notes: 1. This drawing is for general information only; refer to JEDEC Drawing MS-001, Variation BA, for additional information. 2. Dimensions ...
Page 22
JEDEC SOIC Figure 16. 8S1 – JEDECSOIC e Side View Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc. 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, ...
Page 23
TSSOP Figure 17. 8A2 – TSSOP Pin 1 indicator this corner N Top View Side View Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, ...
Page 24
Mini Map Figure 18. 8Y6 – Mini Map D Notes: 1. This drawing is for general information only. Refer to JEDEC Drawing MO-229, for proper dimensions, tolerances, datums, etc. 2. Dimension b applies to metallized terminal and is ...
Page 25
SOT23 Figure 19. 5TS1 – SOT23 E1 Seating Plane NOTES: 1. This d rawing is for gene ral information onl y. Re fer to JEDEC D rawing MO-193, Variation A B, for additional in formation. 2. Dimension D ...
Page 26
Dbga2 Figure 20. 8U3-1 – Dbga2 PIN 1 BALL PAD CORNER PIN 1 BALL PAD CORNER 1 2 (d1 (e1) Bottom SOLDER BALLS 1. Dimension “b” is measured at the maxi ...
Page 27
... Comments Corrected AC Characteristics, T minimum value from 0.55 to 0.05 AA Corrected AT24C08B Part Marking Scheme Add AT24C08B Device Package Marking Details and removed Bumped wafer offering. Update into MS Format. Removed ‘Preliminary’ status Text changes on page 4 and 9 Updated to new template Updated common Figures ...
Page 28
... POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel’s products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life. © ...