TQM829007-PCB TriQuint Semiconductor, TQM829007-PCB Datasheet
TQM829007-PCB
Specifications of TQM829007-PCB
Related parts for TQM829007-PCB
TQM829007-PCB Summary of contents
Page 1
... The Ordering Information Part No. Description TQM829007 0.6-1.0 GHz Digital Variable Gain Amp Fully Assembled Evaluation Board TQM829007-PCB Includes USB control board (EVH) Standard T/R size = 2500 pieces on a 13” reel 12- Disclaimer: Subject to change without notice Connecting the Digital World to the Global Network 21 ...
Page 2
... TQM829007 0.6-1.0GHz ¼W Digital Variable Gain Amplifier Specifications Absolute Maximum Ratings Parameter Storage Temperature RF Input Power, CW, 50Ω,T = 25ºC Vcc (pins 8, 14, 28) Digital Input Voltage Operation of this device outside the parameter ranges given above may cause permanent damage. Electrical Specifications Test conditions unless otherwise noted: 25º ...
Page 3
... Different ground pins are used for SPI (digital) and analog supply voltages. 6. The primary RF microstrip characteristic line impedance is 50 Ω. 7. The single power supply is used to provide supply voltage to AMP1 and AMP2. Bill of Material: TQM829007-PCB Reference Desg. Value ...
Page 4
... TQM829007 0.6-1.0GHz ¼W Digital Variable Gain Amplifier Typical Performance, Maximum Gain State Frequency Gain Input Return Loss Output Return Loss Output P1dB Output IP3 @ Pout = 11 dBm/tone, ∆ MHz Noise Figure Supply Voltage Supply Current Note: 1. The evaluation board can be used with TriQuint’s USB interface board. Refer to TriQuint’s website for more information. ...
Page 5
... TQM829007 0.6-1.0GHz ¼W Digital Variable Gain Amplifier S22 vs. Freq over Attenuation States 0 Temp 0dB 0.5dB -5 4dB 8dB -10 -15 -20 -25 0.6 0.7 0.8 Frequency (GHz) OIP3 vs. Frequency 50 ° +85 C ° + ° − 0.6 0.7 0.8 Frequency (GHz) P1dB vs. Frequency 27 Maximum Gain State ...
Page 6
... TQM829007 0.6-1.0GHz ¼W Digital Variable Gain Amplifier Serial Control Interface SERIN (MSB in First 6-Bit Word) Control Logic Truth Table 6-Bit Control Word to DSA MSB ...
Page 7
... TQM829007 0.6-1.0GHz ¼W Digital Variable Gain Amplifier Serial Control Timing Characteristics Test conditions: 25ºC Parameter Clock Frequency LE Setup Time, t LESUP LE Pulse Width, t LEPW SERIN set-up time, t SDSUP SERIN hold-time, t SDHLD LE Pulse Spacing t LE Propagation Delay t PLO Serial Control DC Logic Characteristics Test conditions: 25ºC ...
Page 8
... Digital Variable Gain Amplifier Detailed Device Description The TQM829007 Ω internally matched digital variable gain amplifier (DVGA) featuring high linearity over the entire gain control range. The amplifier module features the integration of a low noise amplifier gain block, a digital-step attenuator, along with a high linearity ¼ ...
Page 9
... TQM829007 0.6-1.0GHz ¼W Digital Variable Gain Amplifier Detailed Device Description AMP1 AMP1 is a wide band low noise amplifier gain block in DVGA module. The amplifier provides 14.5 dB gain, 2.0 dB noise figure, +40.6 dBm OIP3 at 0.9 GHz while only drawing 85 mA current. External DC blocks and biasing is not required. ...
Page 10
... TQM829007 0.6-1.0GHz ¼W Digital Variable Gain Amplifier Pin Configuration and Description Pin Symbol Description Serial Latch Enable Input. When LE is high, latch is clear and content of SPI control the attenuator When LE is low, data in SPI is latched. Serial data input. The data and clock pins allow the data to be entered serially into SPI and is ...
Page 11
... The component will be laser “TQM829007” product label with an alphanumeric lot code on the top surface of the package. PCB Mounting Pattern Notes: 1. All dimensions are in millimeters. Angles are in degrees. 2. Use 1 oz. copper minimum for top and bottom layer metal. ...
Page 12
... TQM829007 0.6-1.0GHz ¼W Digital Variable Gain Amplifier Product Compliance Information ESD Information ESD Rating: Class 1C Value: Passes ≥ 1000 V to < 2000 V Test: Human Body Model (HBM) Standard: JEDEC Standard JESD22-A114 ESD Rating: Class IV Value: Passes ≥ 1000 V Test: Charged Device Model (CDM) ...