MIKROE-1205 mikroElektronika, MIKROE-1205 Datasheet - Page 20

• Manufacturer Part Number: MIKROE-1205
• Description: Development Boards & Kits - PIC / DSPIC EasyPIC FUSION v7 dsPIC33 PIC24 PIC32
• Manufacturer: mikroElektronika

Specifications of MIKROE-1205

• Rohs: yes
• Product: Development Boards
• Tool Is For Evaluation Of: PIC24x, dsPIC33x, PIC32MX4xx, PIC32MX7xx
• Interface Type: CAN, I2C, SPI
• Operating Supply Voltage: 7 V to 23 V
• Data Bus Width: 16 bit, 32 bit
• Dimensions: 266 mm x 220 mm
• For Use With: PIC24x, dsPIC33x, PIC32MX4xx, PIC32MX7xx

page 20
mikroBUS
Easier connectivity and simple configuration
are imperative in modern electronic devices.
Success of the USB standard comes from it’s
simplicity of usage and high and reliable data
transfer rates. As we in mikroElektronika see it,
Plug-and-Play devices with minimum settings
are the future in embedded world too. This is
why our engineers have come up with a simple,
but brilliant pinout with lines that most of
today’s accessory boards require, which almost
completely eliminates the need of additional
hardware settings. We called this new standard
the mikroBUS
mikroBUS
can see, there are no additional DIP switches,
or jumper selections. Everything is already
™
with two on-board sockets. As you
™
. EasyPIC Fusion
™
v7 supports
routed to the most appropriate pins of the
microcontroller sockets.
mikroBUS
Each mikroBUS
1x8 female headers containing pins that are
most likely to be used in the target accessory
board. There are three groups of communication
pins: SPI, UART and I
are also single pins for PWM, Interrupt,
Analog input, Reset and Chip Select. Pinout
contains two power groups: +5V and GND on
one header and +3.3V and GND on the other
1x8 header.
™
RB8
RC1
RC2
SCK
MISO
MOSI
VCC-3.3V
sockets
™
™
host connector consists of two
host connector
2
AN
RST
CS
SCK
MISO
MOSI
3.3V
GND
C communication. There
1
PWM
GND
SDA
INT
SCL
RX
TX
5V
Integrate mikroBUS
mikroBUS
freely place mikroBUS
clearly mark them with mikroBUS
information, logo artwork and PCB files visit our web site:
http://www.mikroe.com/mikrobus
VCC-5V
RD0
RE8
RF4
RF5
RA2
RA3
™
is not made to be only a part of our development boards. You can
RB9
RC3
RC4
SCK
MISO
MOSI
VCC-3.3V
mikroBUS
AN
RST
CS
SCK
MISO
MOSI
+3.3V
GND
- SPI Chip Select line
- Analog pin
- Reset pin
- SPI Clock line
- Reference Ground
- SPI Slave Output line
- SPI Slave Input line
™
- VCC-3.3V power line
host connectors in your final PCB designs, as long as you
AN
RST
CS
SCK
MISO
MOSI
3.3V
GND
™
™
2
in your design
™
pinout explained
logo and footprint specifications. For more
PWM
GND
SDA
INT
SCL
RX
TX
5V
PWM
INT
RX
TX
SCL
SDA
+5V
GND
VCC-5V
RF12
RF13
- UART Transmit line
- UART Receive line
RD1
RE9
RA2
RA3
- Hardware Interrupt line
- I2C Clock line
- I2C Data line
- VCC-5V power line
- Reference Ground
- PWM output line
DATA BUS
Figure 7-1:
connection
mikroBUS
schematic
™
v7