LFE2M50E-PS-EVN Lattice, LFE2M50E-PS-EVN Datasheet - Page 72
LFE2M50E-PS-EVN
Manufacturer Part Number
LFE2M50E-PS-EVN
Description
Programmable Logic IC Development Tools LatticeECP2M PCI Express Dev Kit
Manufacturer
Lattice
Datasheet
1.LFE2M50E-PS-EVN.pdf
(77 pages)
Specifications of LFE2M50E-PS-EVN
Rohs
yes
Tool Is For Evaluation Of
LatticeECP2M-50
Factory Pack Quantity
1
- Current page: 72 of 77
- Download datasheet (2Mb)
Troubleshooting
LatticeECP2M PCI Express Development Kit User’s Guide
Troubleshooting Driver Installation
Troubleshooting Demo Operation
If they are not listed, shut down the system and try another slot. If the
board is present, check its Properties and the Resource tab to verify
memory was assigned to it. Also verify the Vendor ID and Device ID are
valid, as seen be Windows Plug-n-Play. If the values are invalid, the
bitstream may be corrupt and may need to be reloaded into SPI flash.
The solutions board must be connected to the PC and recognized by
Windows for the driver to be successfully installed. If you do not see the
“Found New Hardware” message when logging in after installing the
board, check the board LEDs. Try a different PCI Express slot.
Make sure you specify the search location for the driver during installation.
Specify that Windows should install from the
Demonstation\<demo_name>\Drivers directory.
You must have Administrator privileges to install device driver files.
The solutions board must be installed inthe PC and recognized by
Windows for the driver to be successfully installed/loaded. The driver must
be loaded by Windows to run the demo. Verify that Windows sees the
board and has loaded a driver for it. See section “Troubleshooting the
Solutions Board” on page 63.
If the GUI displays the error message, “ERROR LOADING
LIBRARY:Cpp_Jni - running in View Only mode” when executed, then the
driver was not found or loaded. There are two causes:
In either case, the board needs to be installed and seen by Windows and
the LSC_PCIe driver needs to be associated with the hardware.
The driver was never loaded (or solutions board is not installed)
The board failed to be detected by Windows.
64
Related parts for LFE2M50E-PS-EVN
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
IC, LATTICEECP2M FPGA, 420MHZ, FPBGA-900
Manufacturer:
LATTICE SEMICONDUCTOR
Datasheet:
Part Number:
Description:
IC, LATTICEECP2M FPGA, 420MHZ, FPBGA-484
Manufacturer:
LATTICE SEMICONDUCTOR
Datasheet:
Part Number:
Description:
Development Software SERDES Eval Board
Manufacturer:
Lattice
Part Number:
Description:
MCU, MPU & DSP Development Tools LatticeECP2M50 SERDES EVAL BRD
Manufacturer:
Lattice
Part Number:
Description:
MCU, MPU & DSP Development Tools LatticeECP2M50 PCI Express x4 EVAL BRD
Manufacturer:
Lattice
Part Number:
Description:
FPGA LatticeECP2M Family 48000 Cells 90nm (CMOS) Technology 1.2V 672-Pin FBGA
Manufacturer:
LATTICE SEMICONDUCTOR
Datasheet:
Part Number:
Description:
FPGA LatticeECP2M Family 48000 Cells 90nm (CMOS) Technology 1.2V 484-Pin FBGA
Manufacturer:
LATTICE SEMICONDUCTOR
Datasheet:
Part Number:
Description:
IC FPGA 50KLUTS 372I/O 672-BGA
Manufacturer:
Lattice
Datasheet:
Part Number:
Description:
IC FPGA 50KLUTS 270I/O 484-BGA
Manufacturer:
Lattice
Datasheet:
Part Number:
Description:
IC FPGA 50KLUTS 270I/O 484-BGA
Manufacturer:
Lattice
Datasheet:
Part Number:
Description:
IC FPGA 50KLUTS 372I/O 672-BGA
Manufacturer:
Lattice
Datasheet:
Part Number:
Description:
IC FPGA 50KLUTS 270I/O 484-BGA
Manufacturer:
Lattice
Datasheet:
Part Number:
Description:
IC FPGA 50KLUTS 270I/O 484-BGA
Manufacturer:
Lattice
Datasheet: