IS42S16400F-7TL-TR ISSI, Integrated Silicon Solution Inc, IS42S16400F-7TL-TR Datasheet - Page 18

• Manufacturer Part Number: IS42S16400F-7TL-TR
• Description: IC SDRAM 64MBIT 143MHZ 54TSOP
• Manufacturer: ISSI, Integrated Silicon Solution Inc
• Type: SDRAMr

Specifications of IS42S16400F-7TL-TR

• Format - Memory: RAM
• Memory Type: SDRAM
• Memory Size: 64M (4M x 16)
• Speed: 143MHz
• Interface: Parallel
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 54-TSOP II
• Organization: 4Mx16
• Density: 64Mb
• Address Bus: 14b
• Access Time (max): 6/5.4ns
• Maximum Clock Rate: 143MHz
• Operating Supply Voltage (typ): 3.3V
• Package Type: TSOP-II
• Operating Temp Range: 0C to 70C
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Supply Current: 100mA
• Pin Count: 54
• Mounting: Surface Mount
• Operating Temperature Classification: Commercial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

IS42S16400F
IC42S16400F
CAS Latency
The CAS latency is the delay, in clock cycles, between
the registration of a READ command and the availability of
the first piece of output data. The latency can be set to two or
three clocks.
If a READ command is registered at clock edge n, and
the latency is m clocks, the data will be available by clock
edge n + m. The DQs will start driving as a result of the
clock edge one cycle earlier (n + m - 1), and provided that
the relevant access times are met, the data will be valid by
clock edge n + m. For example, assuming that the clock
cycle time is such that all relevant access times are met,
if a READ command is registered at T0 and the latency
is programmed to two clocks, the DQs will start driving
after T1 and the data will be valid by T2, as shown in CAS
Latency diagrams.The Allowable Operating Frequency
table indicates the operating frequencies at which each
CAS latency setting can be used.
Reserved states should not be used as unknown operation
or incompatibility with future versions may result.
CAS Latency
18
COMMAND
COMMAND
CLK
CLK
DQ
DQ
READ
READ
T0
T0
CAS Latency - 2
NOP
NOP
CAS Latency - 3
T1
T1
t
LZ
t
AC
CAS Latency
Operating Mode
The normal operating mode is selected by setting M7 and M8
to zero; the other combinations of values for M7 and M8 are
reserved for future use and/or test modes. The programmed
burst length applies to both READ and WRITE bursts.
Test modes and reserved states should not be used be-
cause unknown operation or incompatibility with future
versions may result.
Write Burst Mode
When M9 = 0, the burst length programmed via M0-M2
applies to both READ and WRITE bursts; when M9 = 1,
the programmed burst length applies to READ bursts, but
write accesses are single-location (nonburst) accesses.
NOP
NOP
Speed
T2
T2
Allowable Operating Frequency (MHz)
Integrated Silicon Solution, Inc. — www.issi.com
5
6
7
D
OUT
t
t
OH
LZ
t
AC
NOP
T3
T3
CAS Latency = 2
D
DON'T CARE
UNDEFINED
OUT
t
OH
133
133
133
T4
CAS Latency = 3
200
166
143
03/19/08
Rev. A