ZFSM-101-2 CEL, ZFSM-101-2 Datasheet - Page 16

• Manufacturer Part Number: ZFSM-101-2
• Description: Zigbee / 802.15.4 Modules 2.4GHz 100mW 3.3Volt Freescale MC13202
• Manufacturer: CEL

Specifications of ZFSM-101-2

• Rohs: yes
• Frequency Band: 2.4 GHz
• Line Of Sight Range: 4000 ft
• Data Rate: 250 kbps
• Sensitivity: - 91 dBm
• Operating Supply Voltage: 2.8 V to 3.6 V
• Supply Current Transmitting: 165 mA
• Supply Current Receiving: 50 mA
• Output Power: 20 dBm
• Antenna Connector Type: PCB
• Maximum Operating Temperature: + 85 C
• Dimensions: 36 mm x 25 mm
• Interface Type: UART
• Minimum Operating Temperature: - 40 C

AGENCy CERTIFICATIONS
FCC Compliance Statement (Part 15.19) Section 7.15 of RSS-GEN
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
Warning (Part 15.21)
Changes or modifications not expressly approved by CEL could void the user's authority to operate the equipment.
20 cm Separation Distance
To comply with FCC/IC RF exposure limits for general population/uncontrolled exposure, the antenna(s) used for this trans-
mitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or
operating in conjunction with any other antenna or transmitter.
OEM Responsibility to the FCC Rules and Regulations
The FreeStar Module has been certified per FCC Part 15 rules for integration into products without further testing or certifi-
cation. To fulfill the FCC certification requirements, the OEM of the FreeStar Module must ensure that the
information provided on the FreeStar Label is placed on the outside of the final product. The FreeStar Module is labeled
with its own FCC ID Number. If the FCC ID is not visible when the module is installed inside another device, then the out-
side of the device into which the module is installed must also display a label referring to the enclosed module. This exterior
label can use wording such as the following: “Contains Transmitter Module FCC ID: TFB-FREESTAR” or “Contains FCC ID:
TFB-FREESTAR”
The OEM of the FreeStar Module must only use the approved antenna, that has been certified with this module. The OEM
of the FreeStar Module must test their final product configuration to comply with Unintentional Radiator Limits before declaring
FCC compliance per Part 15 of the FCC rules.
IC Certification — Industry Canada Statement
The term "IC" before the certification/registration number only signifies that the Industry Canada technical specifications
were met.
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two con-
ditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference
that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement
Section 14 of RSS-210
The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in
excess of Health Canada limits for the general population. Consult Safety Code 6, obtainable from Health Canada's
website:
EMC Certification
FCC Part 15.247 Module Certified (Portable)
EN 300 328 1 Certified / CE Approved
Moisture Sensitivity Level (MSL)
MSL 3, per J-STD-033
http://www.hc-sc.gc.ca/ewh-semt/pubs/radiation/99ehd-dhm237/index-eng.php
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.
FreeStar ZFSM-101-2
Page 16