MAX17058EVKIT# Maxim Integrated, MAX17058EVKIT# Datasheet
MAX17058EVKIT#
Specifications of MAX17058EVKIT#
Related parts for MAX17058EVKIT#
MAX17058EVKIT# Summary of contents
Page 1
... Digital Still and Video Cameras Portable Medical Equipment ModelGauge is a trademark of Maxim Integrated Products, Inc. For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com ...
Page 2
ABSOLUTE MAXIMUM RATINGS CELL to GND .........................................................-0.3V to +12V V , SCL, SDA, ALRT to GND .................................-0.3V to +6V IN Continuous Sink Current, SDA, ALRT ................................20mA Operating Temperature Range .......................... -40NC to +85NC Stresses beyond those listed under “Absolute Maximum ...
Page 3
ELECTRICAL CHARACTERISTICS (I (2.5V < V < 4.5V, -20NC < T < +70NC, unless otherwise noted.) (Note PARAMETER High Period of SCL Clock Setup Time for a Repeated START Condition Data Hold Time Data Setup Time Rise ...
Page 4
Sanyo UF504553F, unless otherwise noted.) A QUIESCENT CURRENT vs. SUPPLY VOLTAGE (ACTIVE MODE -20° 2.5 3.0 3.5 V CELL SOC ACCURACY T REFERENCE ...
Page 5
Sanyo UF504553F, unless otherwise noted.) A ZIGZAG PATTERN SOC ACCURACY (1/3) REFERENCE SOC MODELGAUGE SOC 100 TIME (Hr) ZIGZAG PATTERN SOC ACCURACY (3/3) REFERENCE SOC MODELGAUGE SOC ...
Page 6
TOP VIEW (PAD SIDE DOWN) SDA CTG PIN/BUMP NAME TDFN WLP 1 A1 CTG 1 A2 CELL GND 5 B4 ALRT 6 B3 QSTRT 7 B2 SCL 8 B1 SDA — ...
Page 7
Detailed Description ModelGauge Theory of Operation The MAX17058/MAX17059 ICs simulate the internal, non- linear dynamics of a Li+ battery to determine its state of charge (SOC). The sophisticated battery model consid- ers impedance and the slow rate of chemical reactions ...
Page 8
Temperature Compensation For best performance, the host microcontroller must measure battery temperature periodically, and compensate the RCOMP ModelGauge parameter accordingly, at least once per minute. Each custom model defines constants RCOMP0, TempCEach custom model defines constants RCOMP0 (default is 0x97), ...
Page 9
Battery-Swap Detection If V falls below V then returns above V CELL RST quick-starts. This handles the battery swap; the SOC of the previous battery doesn not affect that of the new one. See the Quick-Start and VRESET Register (0x18) ...
Page 10
In sleep mode, the IC halts all operations, reducing current consumption (below 1FA). After exiting sleep mode, the IC continues normal operation. In sleep mode, the IC does not detect self-discharge. If the battery changes state while the IC sleeps, ...
Page 11
VERSION Register (0x08) The value of this read-only register indicates the production version of the IC (0x0011). CONFIG Register (0x0C) See Figure 9. • RCOMP compensates the model for different lithium chemistries. The system must adjust RCOMP periodi- cally (see ...
Page 12
TABLE Registers (0x40 to 0x7F) Contact Maxim for details on how to configure these registers. The default value is appropriate for some Li+ batteries. To unlock the TABLE registers, write 0x57 to address 0x3F, and 0x4A to address 0x3E. While ...
Page 13
I 2 The I C bus system supports operation as a slave-only device in a single or multislave, and single or multimaster system. Slave devices can share the bus by uniquely setting the 7-bit slave address. The I sists of ...
Page 14
Table Protocol Key KEY DESCRIPTION S START bit SAddr Slave address (7 bit) MAddr Memory address byte Data Data byte written by master A Acknowledge bit—master N No acknowledge—master The ICs are compatible with any bus ...
Page 15
Read Data Protocol The read data protocol is used to read to register from the ICs starting at the memory address specified by MAddr. Both register bytes must be read in the same transaction for the register data to be ...
Page 16
... Maxim reserves the right to change the circuitry and specifications without notice at any time. The parametric values (min and max limits) shown in the Electrical Characteristics table are guaranteed. Other parametric values quoted in this data sheet are provided for guidance. Maxim Integrated Products, Inc. 160 Rio Robles, San Jose, CA 95134 USA 1-408-601-1000 © ...