MA300E12_EVAL Infineon Technologies, MA300E12_EVAL Datasheet
MA300E12_EVAL
Related parts for MA300E12_EVAL
MA300E12_EVAL Summary of contents
Page 1
Application Note AN 2007-06 V1.2, June 2010 AN2007-06 MA300E12 / MA300E17 – Module Adapter Board for TM PrimePACK IGBT Modules IFAG IMM INP M AE ...
Page 2
... Warnings Due to technical requirements components may contain dangerous substances. For information on the types in question please contact your nearest Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life- support device or system affect the safety or effectiveness of that device or system ...
Page 3
Module Adapter Board TM for PrimePACK IGBT Modules Table of contents 1 INTRODUCTION.............................................................................................................................. 4 2 DESIGN FEATURES ....................................................................................................................... 5 2.1 Main features ........................................................................................................................ 5 2.2 Key data ................................................................................................................................ 6 2.3 Mechanical dimensions and mounting procedure ........................................................... 6 2.4 Pin assignment..................................................................................................................... ...
Page 4
Module Adapter Board TM for PrimePACK IGBT Modules 1 Introduction The MA300E12 and MA300E17 are developed for 1200V and 1700V PrimePACK™ modules. Used together with the 2ED300E17-SFO evaluation adapter board and 2ED300C17-S /-ST EiceDRIVER™ makes the ‘Flexible driver Starter Kit’ ...
Page 5
Module Adapter Board TM for PrimePACK IGBT Modules Figure 2 The ‘Flexible driver Starter Kit’ for PrimePACK™ module 2 Design features Electrical features of the evaluation board and mechanical dimensions including necessary interface connections are presented in the following sections. ...
Page 6
Module Adapter Board TM for PrimePACK IGBT Modules 2.2 Key data All values given in the table below are typical values, measured at T Table 1 General key data and characteristic values Parameter V max. DC voltage supply DC I ...
Page 7
Module Adapter Board TM for PrimePACK IGBT Modules 132mm max. 12mm Figure 4 Dimensions of the MA300Exx module adapter board 2.4 Pin assignment After the module adapter has been correctly mounted to the PrimePACK™ module all external electrical control signals ...
Page 8
Module Adapter Board TM for PrimePACK IGBT Modules X3 X3 2ED300E17-SFO 2ED300E17-SFO X4 X4 Figure 5 Connections between 2ED300E17-SFO and MA300Exx Figure 6 MA300 Module Adapter board and external electrical connections Table 2 MA300Exx and the external electrical signals description ...
Page 9
Module Adapter Board TM for PrimePACK IGBT Modules 3 Application Note 3.1 Functionality on board The MA300Exx basically supports already existing IGBT driver in half-bridge configuration and provides additional functions separately for both channels (top and bottom IGBT): Gate resistors ...
Page 10
Module Adapter Board TM for PrimePACK IGBT Modules The values of R and R for 1200V module types are the same and therefore assembly of diodes Gon Goff D5, D25, D6, D26 are not needed. External gate resistor suggested values ...
Page 11
Module Adapter Board TM for PrimePACK IGBT Modules 3.4 V monitoring for short circuit detection CE If the IGBT transistor conducts a current a few times higher than the nominal value, the transistor desaturates and the V voltage increases. This ...
Page 12
Module Adapter Board TM for PrimePACK IGBT Modules 0.2µs/div 0.2µs/div Figure 10 Switching off behavior of the FF1000R17IE4 PrimePACK™ module with boosted active clamping where: V 3.6 Maximum switching frequency The switching frequency of an IGBT is limited either by ...
Page 13
Module Adapter Board TM for PrimePACK IGBT Modules Board Temperature vs External Gate Resistor Losses @ Tbaseplate=125°C 110 105 105°C on board (FR4) 100 Figure 11 PCB temperature vs. gate resistor ...
Page 14
Module Adapter Board TM for PrimePACK IGBT Modules The driving power increases accordingly to the number of paralleled modules and their switching frequency. The maximum switching frequency in this case is determined by the PCB temperature and the available driving ...
Page 15
Module Adapter Board TM for PrimePACK IGBT Modules 3.8 Parallel operation 9 The Flexible Starter Kit can be used for driving one PrimePACK™ module as shown on Fig three paralleled PrimePACK™ modules. In this case all ...
Page 16
Module Adapter Board TM for PrimePACK IGBT Modules 4.1 Schematic Figure 13 The MA300Exx – top IGBT Figure 14 The MA300Exx – bottom IGBT Application Note AN 2007-06 16 V1.2, June 2010 ...
Page 17
Module Adapter Board TM for PrimePACK IGBT Modules Figure 15 The MA300Exx – main connectors Figure 16 The MA300Exx – external connectors Application Note AN 2007-06 17 V1.2, June 2010 ...
Page 18
... Table 3 and active clamping diodes should be assembled accordingly to Table 7. Table 7 Assembly Active clamping diodes on the MA300Exx board Board Names MA300E12_EVAL ZD1, ZD2, ZD3, ZD4 ZD21, ZD22, ZD23, ZD24 ZD1, ZD2, ZD3, ZD21, ZD22, ZD23 MA300E17_EVAL Figure 17 The MA300Exx – assembly drawing ...
Page 19
Module Adapter Board TM for PrimePACK IGBT Modules 4.3 Layout Figure 18 The MA300Exx – Top layer Figure 19 The MA300Exx – Bottom layer Application Note AN 2007-06 19 V1.2, June 2010 ...
Page 20
Module Adapter Board TM for PrimePACK IGBT Modules 4.4 Bill of Material - MA300E12 The bill of material includes a part list as well as assembly notes. The tolerances for resistors should be less or equal to ±1 %, for ...
Page 21
Module Adapter Board TM for PrimePACK IGBT Modules 4.5 Bill of Material - MA300E17 The bill of material includes a part list as well as assembly notes. The tolerances for resistors should be less or equal to ±1 %, for ...
Page 22
Module Adapter Board TM for PrimePACK IGBT Modules 5 How to order Evaluation Driver Boards Every Evaluation Driver Board has its own IFX order number and can be ordered via your Infineon Sales Partner. Information can also be found at ...