M25P40-VMN6TPB NUMONYX, M25P40-VMN6TPB Datasheet - Page 10
![IC FLASH 4MBIT 75MHZ 8SOIC](/photos/7/28/72827/m25p40-vmn6tp_sml.jpg)
M25P40-VMN6TPB
Manufacturer Part Number
M25P40-VMN6TPB
Description
IC FLASH 4MBIT 75MHZ 8SOIC
Manufacturer
NUMONYX
Series
Forté™r
Datasheet
1.M25P40-VMP6G.pdf
(61 pages)
Specifications of M25P40-VMN6TPB
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
4M (512K x 8)
Speed
75MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.3 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (3.9mm Width)
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
M25P40-VMN6TPBTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M25P40-VMN6TPB
Manufacturer:
MICRON
Quantity:
21 000
Company:
Part Number:
M25P40-VMN6TPB
Manufacturer:
MICRON
Quantity:
11 200
Company:
Part Number:
M25P40-VMN6TPB
Manufacturer:
Numonyx
Quantity:
22 500
Company:
Part Number:
M25P40-VMN6TPB
Manufacturer:
MICRON44
Quantity:
18 188
Part Number:
M25P40-VMN6TPB
Manufacturer:
MICRON
Quantity:
20 000
3
10/61
SPI modes
These devices can be driven by a microcontroller with its SPI peripheral running in either of
the two following modes:
For these two modes, input data is latched in on the rising edge of Serial Clock (C), and
output data is available from the falling edge of Serial Clock (C).
The difference between the two modes, as shown in
bus master is in Stand-by mode and not transferring data:
Figure 3.
1. The Write Protect (W) and Hold (HOLD) signals should be driven, High or Low as appropriate.
Figure 3: Bus Master and memory devices on the SPI bus
devices connected to an MCU, on an SPI bus. Only one device is selected at a time, so only
one device drives the Serial Data output (Q) line at a time, the other devices are high
impedance. Resistors R (represented in
the Bus Master leaves the S line in the high impedance state. As the Bus Master may enter
a state where all inputs/outputs are in high impedance at the same time (for example, when
the Bus Master is reset), the clock line (C) must be connected to an external pull-down
resistor so that, when all inputs/outputs become high impedance, the S line is pulled High
while the C line is pulled Low (thus ensuring that S and C do not become High at the same
time, and so, that the t
that the time constant R*C
time during which the Bus Master leaves the SPI bus in high impedance.
SPI Interface with
CS3
(CPOL, CPHA) =
SPI Bus Master
(0, 0) or (1, 1)
CPOL=0, CPHA=0
CPOL=1, CPHA=1
C remains at 0 for (CPOL=0, CPHA=0)
C remains at 1 for (CPOL=1, CPHA=1)
CS2 CS1
Bus Master and memory devices on the SPI bus
SDO
SDI
SCK
R
SHCH
R
p
requirement is met). The typical value of R is 100K Ω, assuming
(C
C Q D
S
p
SPI Memory
= parasitic capacitance of the bus line) is shorter than the
Device
W
V
CC
HOLD
Figure
V
R
SS
3) ensure that the M25P40 is not selected if
C Q D
S
Figure
SPI Memory
Device
W
shows an example of three
4, is the clock polarity when the
V
HOLD
CC
V
R
SS
C Q D
S
SPI Memory
Device
W
V
CC
HOLD
AI12836b
V
SS
V
V
CC
SS