M25PE40-VMW6G NUMONYX, M25PE40-VMW6G Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/4/484/numonyx_sml.jpg)
M25PE40-VMW6G
Manufacturer Part Number
M25PE40-VMW6G
Description
IC FLASH 4MBIT 75MHZ 8SOIC
Manufacturer
NUMONYX
Series
Forté™r
Datasheet
1.M25PE40-VMN6TP.pdf
(62 pages)
Specifications of M25PE40-VMW6G
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
4M (512K x 8)
Speed
75MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
Clock Frequency
75MHz
Supply Voltage Range
2.7V To 3.6V
Memory Case Style
WSOIC
No. Of Pins
8
Operating Temperature Range
-40°C To +85°C
Memory Configuration
512K X 8
Interface Type
Serial, SPI
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
M25PE40
4.8.2
Specific hardware and software protections
The M25PE40 features a Hardware Protected mode, HPM, and two Software Protected
modes, SPM1 and SPM2 that can be combined to protect the memory array as required.
They are described below:
HPM
SPM1 and SPM2
HPM in T7X process (see
The Hardware Protected mode (HPM) is entered when Top Sector Lock (TSL) is driven
Low, causing the top 256 pages of memory to become read-only. When Top Sector
Lock (TSL) is driven High, the top 256 pages of memory behave like the other pages of
memory and the protection depends on the Block Protect bits (see SPM2 below).
HPM in T9HX process (see
The Hardware Protected mode (HPM) is used to write-protect the non-volatile bits of
the Status Register (that is, the Block Protect bits, BP2, BP1 and BP0, and the Status
Register Write Disable bit, SRWD).
HPM is entered by driving the Write Protect (W) signal Low with the SRWD bit set to
High. This additional protection allows the Status Register to be hardware-protected
(see also
The first Software Protected mode (SPM1) is managed by specific Lock Registers
assigned to each 64-Kbyte sector.
The Lock Registers can be read and written using the Read Lock Register (RDLR) and
Write to Lock Register (WRLR) instructions.
In each Lock Register two bits control the protection of each sector: the Write Lock bit
and the Lock Down bit.
–
–
The Write Lock bit and the Lock Down bit are volatile and their value is reset to ‘0’ after
a power-down or a reset.
Write Lock bit:
The Write Lock bit determines whether the contents of the sector can be modified
(using the Write, Program or Erase instructions). When the Write Lock bit is set to
‘1’, the sector is write protected – any operations that attempt to change the data
in the sector will fail. When the Write Lock bit is reset to ‘0’, the sector is not write
protected by the Lock Register, and may be modified.
Lock Down bit:
The Lock Down bit provides a mechanism for protecting software data from simple
hacking and malicious attack. When the Lock Down bit is set to ‘1’, further
modification to the Write Lock and Lock Down bits cannot be performed. A reset,
or power-up, is required before changes to these bits can be made. When the
Lock Down bit is reset to ‘0’, the Write Lock and Lock Down bits can be changed.
Section 6.4.4: SRWD
Important note on page
Important note on page
bit).
6):
6):
Operating features
15/62