M45PE40-VMP6TG NUMONYX, M45PE40-VMP6TG Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/4/484/numonyx_sml.jpg)
M45PE40-VMP6TG
Manufacturer Part Number
M45PE40-VMP6TG
Description
IC FLASH 4MBIT 75MHZ 8VFQFPN
Manufacturer
NUMONYX
Series
Forté™r
Datasheet
1.M45PE40-VMP6G.pdf
(49 pages)
Specifications of M45PE40-VMP6TG
Format - Memory
FLASH
Memory Type
FLASH
Memory Size
4M (512K x 8)
Speed
75MHz
Interface
SPI, 3-Wire Serial
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-VFQFN, 8-VFQFPN
Cell Type
NOR
Density
4Mb
Access Time (max)
8ns
Interface Type
Serial (SPI)
Boot Type
Not Required
Address Bus
1b
Operating Supply Voltage (typ)
3.3V
Operating Temp Range
-40C to 85C
Package Type
VFQFPN EP
Sync/async
Synchronous
Operating Temperature Classification
Industrial
Operating Supply Voltage (min)
2.7V
Operating Supply Voltage (max)
3.6V
Word Size
8b
Number Of Words
512K
Supply Current
8mA
Mounting
Surface Mount
Pin Count
8
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
M45PE40-VMP6TG
M45PE40-VMP6TGTR
M45PE40-VMP6TGTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M45PE40-VMP6TG
Manufacturer:
Micron Technology Inc
Quantity:
10 000
Signal descriptions
2
2.1
2.2
2.3
2.4
2.5
2.6
8/49
Signal descriptions
Serial data output (Q)
This output signal is used to transfer data serially out of the device. Data is shifted out on the
falling edge of Serial Clock (C).
Serial data input (D)
This input signal is used to transfer data serially into the device. It receives instructions,
addresses, and the data to be programmed. Values are latched on the rising edge of Serial
Clock (C).
Serial Clock (C)
This input signal provides the timing of the serial interface. Instructions, addresses, or data
present at serial data input (D) are latched on the rising edge of Serial Clock (C). Data on
serial data output (Q) changes after the falling edge of Serial Clock (C).
Chip Select (S)
When this input signal is High, the device is deselected and serial data output (Q) is at high
impedance. Unless an internal read, program, erase or write cycle is in progress, the device
will be in the standby power mode (this is not the deep power-down mode). Driving Chip
Select (S) Low selects the device, placing it in the active power mode.
After power-up, a falling edge on Chip Select (S) is required prior to the start of any
instruction.
Reset (Reset)
The Reset (Reset) input provides a hardware reset for the memory. In this mode, the outputs
are high impedance.
When Reset (Reset) is driven High, the memory is in the normal operating mode. When
Reset (Reset) is driven Low, the memory will enter the reset mode, provided that no internal
operation is currently in progress. Driving Reset (Reset) Low while an internal operation is in
progress has no effect on that internal operation (a write cycle, program cycle, or erase
cycle).
Write Protect (W)
This input signal puts the device in the hardware protected mode, when Write Protect (W) is
connected to V
them from write, program and erase operations. When Write Protect (W) is connected to
V
CC
, the first 256 pages of memory behave like the other pages of memory.
SS
, causing the first 256 pages of memory to become read-only by protecting
M45PE40