M29DW323DB70N6E NUMONYX, M29DW323DB70N6E Datasheet - Page 13
![IC FLASH 32MBIT 70NS 48TSOP](/photos/7/28/72853/m29dw323db70n6_sml.jpg)
M29DW323DB70N6E
Manufacturer Part Number
M29DW323DB70N6E
Description
IC FLASH 32MBIT 70NS 48TSOP
Manufacturer
NUMONYX
Series
Axcell™r
Datasheet
1.M29DW323DT70ZE6F.pdf
(51 pages)
Specifications of M29DW323DB70N6E
Format - Memory
FLASH
Memory Type
FLASH - Nor
Memory Size
32M (4Mx8, 2Mx16)
Speed
70ns
Interface
Parallel
Voltage - Supply
2.7 V ~ 3.6 V
Operating Temperature
-40°C ~ 85°C
Package / Case
48-TSOP
Supply Voltage Range
2.7V To 3.6V
Memory Case Style
TSOP
No. Of Pins
48
Operating Temperature Range
-40°C To +85°C
Access Time
70ns
Memory Configuration
4M X 8, 2M X 16
Interface Type
CFI, Parallel
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M29DW323DB70N6E
Manufacturer:
VISHAY
Quantity:
6 700
Part Number:
M29DW323DB70N6E
Manufacturer:
ST
Quantity:
20 000
BUS OPERATIONS
There are five standard bus operations that control
the device. These are Bus Read, Bus Write, Out-
put Disable, Standby and Automatic Standby.
The Dual Bank architecture of the M29DW323 al-
lows read/write operations in Bank A, while read
operations are being executed in Bank B or vice
versa. Write operations are only allowed in one
bank at a time.
See Tables
ry. Typically glitches of less than 5ns on Chip En-
able or Write Enable are ignored by the memory
and do not affect bus operations.
Bus Read. Bus Read operations read from the
memory cells, or specific registers in the Com-
mand Interface. A valid Bus Read operation in-
volves setting the desired address on the Address
Inputs, applying a Low signal, V
and Output Enable and keeping Write Enable
High, V
value, see
and
tails of when the output becomes valid.
Bus Write. Bus Write operations write to the
Command Interface. A valid Bus Write operation
begins by setting the desired address on the Ad-
dress Inputs. The Address Inputs are latched by
the Command Interface on the falling edge of Chip
Enable or Write Enable, whichever occurs last.
The Data Inputs/Outputs are latched by the Com-
mand Interface on the rising edge of Chip Enable
or Write Enable, whichever occurs first. Output En-
able must remain High, V
Write operation. See Figures
Waveforms, and Tables
Characteristics, for details of the timing require-
ments.
Output Disable. The Data Inputs/Outputs are in
the high impedance state when Output Enable is
High, V
Standby. When Chip Enable is High, V
memory enters Standby mode and the Data In-
puts/Outputs pins are placed in the high-imped-
Table 15., Read AC
IH
IH
. The Data Inputs/Outputs will output the
.
Figure 11., Read Mode AC
3
and 4, Bus Operations, for a summa-
IH
Characteristics, for de-
16
, during the whole Bus
12
and 17, Write AC
IL
and 13, Write AC
, to Chip Enable
Waveforms,
IH
, the
ance state. To reduce the Supply Current to the
Standby Supply Current, I
be held within V
level see
During program or erase operations the memory
will continue to use the Program/Erase Supply
Current, I
til the operation completes.
Automatic Standby. If CMOS levels (V
are used to drive the bus and the bus is inactive for
300ns or more the memory enters Automatic
Standby where the internal Supply Current is re-
duced to the Standby Supply Current, I
Data Inputs/Outputs will still output data if a Bus
Read operation is in progress.
Special Bus Operations
Additional bus operations can be performed to
read the Electronic Signature and also to apply
and remove Block Protection. These bus opera-
tions are intended for use by programming equip-
ment and are not usually used in applications.
They require V
Electronic Signature. The memory has two
codes, the manufacturer code and the device
code, that can be read to identify the memory.
These codes can be read by applying the signals
listed in Tables
Block Protect and Chip Unprotect. Groups
blocks can be protected against accidental Pro-
gram or Erase. The Protection Groups are shown
in
dresses. The whole chip can be unprotected to al-
low the data inside the blocks to be changed.
The V
the two outermost boot blocks. When V
Protect is at V
protected and remain protected regardless of the
Block Protection Status or the Reset/Block Tem-
porary Unprotect pin status.
Block Protect and Chip Unprotect operations are
described in
APPENDIX
PP
/Write Protect pin can be used to protect
CC3
Table 14., DC
APPENDIX D.
, for Program or Erase operations un-
IL
M29DW323DT, M29DW323DB
ID
A., Tables
CC
3
the two outermost boot blocks are
to be applied to some pins.
and 4, Bus Operations.
± 0.2V. For the Standby current
Characteristics.
CC2
23
, Chip Enable should
and 24, Block Ad-
CC
CC2
PP
± 0.2V)
/Write
. The
13/51
of